Abstract:Introduction: In the past three decades, additive manufacturing (AM), also known as 3D printing, has emerged as a promising technology, which allows the manufacture of complex parts by adding material layer upon layer. In comparison, with other metal-based AM technologies, gas metal arc welding-based additive manufacturing (GMAW-based AM) presents a high deposition rate and has the potential for producing medium and large metal components. To validate the technological performance of such a manufacturing process, the internal quality of manufactured parts needs to be analyzed, particularly in the cases of manufacturing the parts working in a critical load-bearing condition. Therefore, this paper aims at investigating the internal quality (i.e., and mechanical properties) of components manufactured by the GMAW-based AM technology. Method: A gas metal arc welding robot was used to build a thin-walled component made of mild steel on a low-carbon substrate according to the AM principle. Thereafter, the specimens for observing and mechanical properties were extracted from the built thin-walled component. The of the specimen were observed by an optical microscope; the hardness was measured by a digital tester, and the tensile tests were carried out on a tensile test machine. Results: The results show that the GMAW-based AM-built thin-walled components possess an adequate that varies from the top to the bottom of the built component: structures with primary dendrites in the upper zone; granular structure of with small regions of at grain boundaries in the middle zone, and grains of in the lower zone. The hardness (ranged between 164±3.46 HV to 192±3.81 HV), yield strength (YS offset of 0.2% ranged from 340±2 to 349.67±1.53 ), and ultimate tensile strength (UTS ranged from 429±1 to 477±2 ) of the GMAW-based AM-built components were comparable to those of wrought mild steel. Conclusions: The results obtained in this study demonstrate that the GMAW-based AM-built components possess adequate and good mechanical properties for real applications. This allows us to confirm the feasibility of using a conventional gas metal arc welding robot for additive manufacturing or repairing/re-manufacturing of metal components.

Study on mechanical properties of deposited metallic objects for different build strategies using semi-automatic welding setup

Manufacture of complex thin-walled metallic objects using weld-deposition based additive manufacturing

Photopolymerization of Stainless Steel 420 Metal Suspension: Printing System and Process Development of Additive Manufacturing Technology toward High-Volume Production

A preliminary study on gas metal arc welding-based additive manufacturing of metal parts

Influence of Scanning Strategies on the Tensile and Fatigue Properties of Direct Metal Laser Sintering-Printed Co-Cr-Mo Alloy

Investigation on influence of selective laser melting parameters on mechanical properties of Ti-6Al-4V alloy

The enhancement of mechanical properties via post-heat treatments of AISI 630 parts printed with material extrusion

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing

The Production of Three-Dimensional Metal Objects Using Oscillatory-Strain-Assisted Fine Wire Shaping and Joining

Microstructural and mechanical characterization of direct energy deposited 316L stainless steel developed using an evolutionary computational approach

Development of paste extrusion-based metal additive manufacturing process

Effect of multi-layer deposition in solid-state friction stir surfacing-based additive manufacturing for fabrication of large-scale metal product

Metals by micro-scale additive manufacturing: comparison of microstructure and mechanical properties

Studies on Tensile Behaviour of Selective Laser Melted 316L Stainless Steel Using SEM Straining Stage

Additive manufacturing: A review on 3 D printing of metals and study of residual stress, buckling load capacity of strut members

Metallurgy, mechanistic models and machine learning in metal printing

A Review on Wire-Fed Directed Energy Deposition Based Metal Additive Manufacturing

The role of tool path on microstructure uniformity in large-format additive manufacturing: integrated thermo-metallurgical-mechanical approach

Computational modelling of shaped metal deposition

Prototyping and characterisation of 316L stainless steel parts and lattice structures printed via metal fused filament fabrication

Bead Modelling and Deposition Path Planning in Wire Arc Additive Manufacturing of Three Dimensional Parts