Abstract:Electrical bearing currents may disturb the performance of the bearings via electro-corrosion if they surpass a limit of ca. 0.1 to 0.3 A/mm2. A continuous current flow, or, after a longer time span, an alternating current or a repeating impulse-like current, damages the raceway surface, leading in many cases to a fluting pattern on the raceway. Increased bearing vibration, audible noise, and decreased bearing lubrication as a result may demand a replacement of the bearings. Here, an electrically corroded axial ball bearing (type 51208) with fluting patterns is investigated. The bearing was lubricated with grease lubrication and was exposed to 4 A DC current flow. It is shown that the electric current flow causes higher concentrations of iron oxides and iron carbides on the bearing raceway surface together with increased surface roughness, leading to a mixed lubrication also at elevated bearing speeds up to 1500 rpm. The "electrically insulating" iron oxide layer and the "mechanically hard" iron carbide layer on the bearing steel are analysed by WLI, XPS, SEM, and EDS. White Light Interferometry (WLI) is used to provide an accurate measurement of the surface topography and roughness. X-ray Photoelectron Spectroscopy (XPS) measurements are conducted to analyze the chemical surface composition and oxidation states. Scanning Electron Microscopy (SEM) is applied for high-resolution imaging of the surface morphology, while the Focused Ion Beam (FIB) is used to cut a trench into the bearing surface to inspect the surface layers. With the Energy Dispersive X-ray spectrometry (EDS), the presence of composing elements is identified, determining their relative concentrations. The electrically-caused iron oxide and iron carbide may develop periodically along the raceway due to the perpendicular vibrations of the rolling ball on the raceway, leading gradually to the fluting pattern. Still, a simulation of this vibration-induced fluting-generation process from the start with the first surface craters—of the molten local contact spots—to the final fluting pattern is missing.

Confirming dark groove microstructural alterations as WEC initiation first stage in cylindrical roller thrust bearings lubricated with WEC critical oil

A Study on Decisive Early Stages in White Etching Crack Formation Induced by Lubrication

The Evolution of White Etching Cracks (WECs) in Rolling Contact Fatigue-Tested 100Cr6 Steel

The effect of electrical current on premature failures and microstructural degradation in bearing steel

The influence of lubricants on white etching areas formation in DLC-coated bearing steel under severe boundary lubrication

Derivative Analysis and Evaluation of Roll-slip Fretting Wear Mechanism of Ultra-thin-walled Bearings under High Service

Analysis and Evaluation of Multi-state Wear Mechanism of Elastic-flexible Thin-walled Bearings

An updated review: white etching cracks (WECs) and axial cracks in wind turbine gearbox bearings

WLI, XPS and SEM/FIB/EDS Surface Characterization of an Electrically Fluted Bearing Raceway

Dark etching regions under rolling contact fatigue: a review

The origin of microstructural alterations in M50 bearing steel undergoing rolling contact fatigue

Tribological and dynamic performance analysis of rolling bearings with varied surface textures operating under lubricant contamination

White Etching Bands Formation Mechanisms Due to Rolling Contact Fatigue

Influence of micro-texture radial depth variations on the tribological and vibration characteristics of rolling bearings under starved lubrication

Microstructure Alterations and White Etching Area Formation in Bearing Steels under High-Frequency Dynamic Loading

Experimental investigations to assess surface fatigue failure in rolling contact bearing

A surface study of failed planetary wind turbine gearbox Bearings to investigate the causes of the Bearing premature failure issue

Structure–performance evolution mechanism of the wear failure process of coated spherical plain bearings

White etching area damage induced by shear localization in rolling contact fatigue of bearing steel

EHD Lubrication Characteristics of a New Type of Ground Cylindrical Worm Gearing

Journal Bearing Wear Monitoring via On-Line Visual Ferrography