An Overview of the Spallation Neutron Source Project

Robert L. Kustom

DOI: https://doi.org/10.48550/arXiv.physics/0008212

2000-08-23

Abstract:The Spallation Neutron Source (SNS) is being designed, constructed, installed and commissioned by the staff of six national laboratories, Argonne National Laboratory, Brookhaven National Laboratory, Jefferson National Accelerator Laboratory, Lawrence Berkeley National Laboratory, Los Alamos National Laboratory, and Oak Ridge National Laboratory. The accelerator systems are designed to deliver a 695 ns proton-pulse onto a mercury target at a 60-Hz repetition rate and an average power of 2-MW. Neutron moderators that will convert the spallation neutrons into slow neutrons for material science research will surround the target. The Front-End systems are designed to generate an H- beam of minipulses, 68% beam on, 32% beam off every 965 ns, at 2.5 MeV for 1 ms, 60 times a second. The Front-End systems include a RF driven, volume-production ion source, beam chopping system, RFQ, and beam transport. The ion source will have to achieve about 65 mA to deliver 52 mA at the input to the linac. The linac consists of a drift tube linac up to 86.8 MeV, a coupled-cell linac to 185 MeV, and a superconducting RF linac to the nominal energy of 1 GeV. The design of the superconducting section includes 11 cryomodules with three, 0.61-beta cavities per cryomodule and 17 cryomodules with four, 0.81-beta cavities per cryomodule, with space to install four more 0.81-beta cryomodules. The accumulator ring is designed for charge exchange injection at full energy. The peak charge per bunch at the end of the accumulation cycle will reach 2.08x10**14 for 2-MW operation. The goal is to control beam losses to less than 1x10**-4.

Accelerator Physics

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is to design and build a high - throughput Spallation Neutron Source (SNS) to provide a stronger neutron beam than any existing spallation neutron sources for materials science research. Specifically, the goals of SNS are:

1. **Provide a high - power proton beam**: Design and implement an accelerator system that can hit a mercury target with proton pulses of 695 nanoseconds (ns) at a repetition frequency of 60 hertz (Hz), with an average power reaching 2 megawatts (MW). Key parameters include:
- Proton beam power: 2 MW
- Average proton beam current: 2 mA
- Pulse repetition frequency: 60 Hz
- Pulse width: 695 ns

2. **Generate slow neutrons**: Convert spallation neutrons into slow neutrons through a neutron buffer for materials science research. SNS will be equipped with 18 neutron beam lines, although initially only 10 instruments are planned to be used.

3. **Reduce uncontrolled beam loss**: Ensure that the beam loss is less than \(1\times10^{- 4}\) to guarantee the safety and stability of the equipment.

To achieve these goals, the SNS project is completed through the cooperation of six national laboratories, involving the complex design and construction of multiple subsystems, including Front - End Systems (FES), Linac, superconducting cavities, Accumulator Ring, etc.

### Key technical challenges and solutions

1. **Front - End Systems (FES)**:
- Design a system to generate H⁻ ion beams, ensuring that micropulses with a 68% duty cycle are generated every 945 nanoseconds.
- Use RF - driven ion sources, beam chopping systems, radio - frequency quadrupoles (RFQ), and Low - Energy Beam Transport systems (LEBT) and Medium - Energy Beam Transport systems (MEBT) to achieve this goal.

2. **Linac**:
- Include Drift - Tube Linac (DTL), Coupled - Cavity Linac (CCL), and Superconducting Radio - Frequency Accelerator (SRF Linac), and finally increase the proton beam energy to approximately 1 GeV.
- The energy gain in the DTL part is 2.3 MeV/m, the energy gain in the CCL part is 1.7 MeV/m, and the SRF part uses superconducting cavities with different β values.

3. **Accumulator Ring**:
- Design an accumulator ring for direct charge - exchange injection, ensuring that \(2.08\times10^{14}\) protons are accumulated during 2 MW operation.
- Adopt a zero - dispersion region and multiple magnet configurations to ensure the stability and uniform distribution of the beam.

In conclusion, this paper describes in detail the design, construction, and commissioning progress of SNS, aiming to provide an unprecedented high - throughput neutron source for materials science research.