Abstract:Waterjet-assisted laser drilling technology facilitates the fabrication of high-quality micro-holes by utilizing the collaborative benefits of waterjets and lasers. In this study, the coaxial waterjet-assisted laser drilling (CWALD) technique was employed to improve the properties of micro-holes during femtosecond laser drilling. Based on computational fluid dynamics (CFD) simulations, the stability of the waterjet was initially verified by optimizing the structure of the watercourse and nozzle shape in the CWALD device. Furthermore, a comparative experiment between laser direct drilling (LDD) and CWALD revealed that while CWALD can produce well-rounded micro-holes with a high aspect ratio, it exhibits lower efficiency and results in a larger heat-affected zone (HAZ). To address these drawbacks associated with CWALD, a two-step coaxial waterjet-assisted composite laser drilling (TS-CWALD) method was proposed. TS-CWALD involves applying CWALD for secondary modification of micro-hole shape following LDD with punching. This modification process is pivotal for enhancing drilling accuracy but requires consideration of multiple parameters. For this purpose, regression models were established for the inlet diameter, outlet diameter, and taper; response surface methodology was then employed to optimize these parameters. Subsequently, interactive effects analysis was conducted on different responses based on laser pulse energy, frequency, modification speed, and number of modification cycles. The adequacy of the developed models was subsequently verified using analysis of variance methods. Finally, the successful fabrication of a film hole with an inlet diameter of 205 μm and an outlet diameter of 200 μm, featuring a taper of only 0.2°, was achieved ultimately through meticulous parameter optimization. Furthermore, the micro-hole retained a minimal HAZ. The optimized parameters encompassed a pulse energy of 20.6 μJ, frequency of 127 kHz, modification speed of 3 mm/s, and shape modification carried out over 335 cycles.

Feasibility study on finishing the inner surface of SLA small holes by volume alternating cavitation shock wave

Novel Bidirectional Volume Alternating Cavitation Technique for the Inner Surface Finishing of Small Holes

Theoretical and Experimental Investigation on a Novel Cavitation-Assisted Abrasive Flow Polishing Method

A Novel Method for Improving Surface Finish of Stereolithography Apparatus

Experimental investigation and optimization of modification during coaxial waterjet-assisted femtosecond laser drilling

Mechanism and feasibility study of low frequency vibration assisted drilling of a newly developed CFRP/Al co-cured material

Fused Deposition Modeling Five-Axis Additive Manufacturing: Machine Design, Fundamental Printing Methods and Critical Process Characteristics

A Vibration-Assisted Separation Method for Constrained-Surface-Based Stereolithography

Controlled hydrodynamic cavitation erosion with abrasive particles for internal surface modification of additive manufactured components

Numerical and Experimental Study on Ultrasonic Vibration-Assisted Micro-Channelling of Glasses Using an Abrasive Slurry Jet

Numerical Modeling and Experimental Study on the Material Removal Process Using Ultrasonic Vibration-Assisted Abrasive Water Jet

Study on the surface integrity of micro-holes in high volume fraction SiCp/Al using ultrasonic vibration drilling

Improving finishing uniformity using fluid field vibration in abrasive water flow polishing of inclined hole

Experiment and Simulation Study of the Laser-Induced Cavitation Bubble Technique for Forming a Microgroove in Aluminum Foil

Dual-directional Ultrasonic Vibration-Assisted Femtosecond Laser Drilling of Film Cooling Holes

Investigation of Surface Integrity of Selective Laser Melting Additively Manufactured AlSi10Mg Alloy under Ultrasonic Elliptical Vibration-Assisted Ultra-Precision Cutting

Study on reducing burrs of super alloy through structures in water jet guided laser ablation

Experimental Investigation on Magnetic Abrasive Finishing for Internal Surfaces of Waveguides Produced by Selective Laser Melting

Design of a Compact 3-D Vibration-Assisted Turning Device with Large Amplitude and High Frequency for Diversified Microstructure Sculpturing

Improvement of process repeatability and resolution in abrasive air jet machining via viscous slurry entrainment

Research Progresses of Finishing Technology for Inner Channel of Additive Manufacturing Parts