Abstract:This paper describes a test program on the stress concentration factors (SCFs) of stainless steel hybrid tubular (SSHT) joints with square hollow section (SHS) braces and circular hollow section (CHS) chord and SSHT joints with CHS braces and SHS chord. The load was applied to the brace for all test specimens. Twenty specimens in total, including ten overlapped and ten gapped tubular K-joints, were tested. Different geometric parameters were used which include brace width-to-chord diameter ratio (beta(1) = b(1)/d(0)), brace-to-chord thickness ratio (tau(1) = t(1)/t(0)) and chord diameter-to-thickness ratio (2 gamma(1) = d(0)/t(0)) for SHS-to-CHS hybrid tubular joints, brace diameter to-chord width ratio (beta(2) = d(1)/b(0)), brace-to-chord thickness ratio (tau(2) = t(1)/t(0)) and chord width-to-thickness ratio (2 gamma(2) = b(0)/t(0)) for CHS-to-SHS hybrid tubular joints. A number of strain gauges were used at the hot spot locations for various tubular joints. The hot spot stress (HSS) method was used to determine the SCFs of SSHT joints using the quadratic extrapolation method. This was a consequence of the stress distributions around the intersection area of SHS-to-CHS and CHS-to-SHS hybrid tubular joints being nonlinear. Results found the maximum SCFs for hybrid overlapped tubular K-joints with square braces and circular chord to be located at the hot spot location at an angle of 135 degrees between the SHS brace and the CHS chord. This is characterized as line A. The maximum SCFs of hybrid gapped tubular K-joints with square braces and circular chord were located at the hot spot location at an angle of 45 degrees between the SHS tension brace and the CHS chord (characterized as line C) and at an angle of 45 degrees between the SHS compression brace and the CHS chord (characterized as line E). The maximum SCFs of hybrid overlapped tubular K-joints with circular braces and square chord were located at the hot spot location at an angle of 180 degrees to the CHS brace. The maximum SCFs of hybrid gapped tubular K-joints with circular braces and square chord were located generally at the hot spot location at an angle of 0 degrees to the CHS brace. Test results were compared against the design predictions in accordance with the current design guidelines of the International Committee for the Development and Study of Tubular Structures (CIDECT, 2001). Upon comparison, it was found that the design formulas of CIDECT (2001) overestimate the maximum SCFs of SHS-to-CHS hybrid gapped tubular K-joints. For the CHS chord and SHS braces of hybrid overlapped tubular K-joints, the design formulas overestimate the maximum SCFs for most of the specimens. Furthermore, for the SHS chord and CHS braces of hybrid gapped tubular K-joints, the design formulas of CIDECT (2001) overestimate the maximum SCFs. For the SHS chord and CHS braces of hybrid overlapped tubular K-joints, the CIDECT (2001) design formulas were unconservative when determining the maximum SCFs of such joints.

Investigation on load-bearing capacity improvement coefficient of CFRP-reinforced CHS KT-joints

Experimental study on CFRP reinforcement and static performance of CHS KT-joints

Experimental investigation of SCF distribution for thin-walled concrete-filled CHS joints under axial tension loading

Study Of Mechanical Performance Of Concrete-Filled Steel Tubular Joints

Mechanical Behaviour and Design of Concrete-Filled K and KK CHS Connections

Parametric study of stress concentration factors in KT connections reinforced with concrete subjected to axial loads

Experimental Investigation and Design of Concrete-Filled Steel Tubular CHS Connections

08.40: Numerical Investigation of Mechanical Properties of Multi‐planar Concrete‐filled Steel Tubular Joints

Load Introduction and Transfer Mechanism of K-type CFST Circular Section Connections

Experimental and numerical analyses on stress concentration factors of concrete-filled welded integral K-joints in steel truss bridges

Flexural Tests and Behavior of Multi-Celled Corrugated-Plate CFST Members

Experimental and Numerical Investigations on Flexural Behaviour of CFRP Reinforced Concrete-Filled Stainless Steel CHS Tubes

Effectiveness and Efficiency of Externally Bonded CFRP Sheets for Shear Strengthening of RC Beam-Column Joints

Effect of sustaining load level on flexural behavior of RC beams retrofitted with CFRP sheets

Effects of Chord Pre-Load on Strength of CHS X-joints Stiffened with External Ring Stiffeners and Gusset Plates

Fatigue tests of multiplanar concrete-filled steel tubular KK-joints with inner ring stiffeners

Experimental and numerical study on static behaviour of uniplanar CFDST-CHS T-joints

Behaviour of CFDST chord to CHS brace composite K-joints: Experiments

Nonlinear behaviour and design of stainless steel hybrid tubular K-joints with SHS-to-CHS

EXPERIMENTAL STUDY ON STEEL CHS SLENDER COLUMNS STRENGTHENED BY CFRP UNDER AXIAL COMPRESSION

An Experimental Study on Stress Concentration Factors of Stainless Steel Hybrid Tubular K-joints