Abstract:A methodology for determining the micropore, mesopore, and external surface areas of hierarchical microporous/mesoporous materials from N2 adsorption isotherms at 77 K is described. For FAU-Y zeolites, the microporous surface area calculated using the Rouquerol criterion and the Brunauer-Emmett-Teller (BET) equation is in accord with the geometrical surface determined by the chord length distribution method. Therefore, BET surface area ( SBET) is the well representative of micropore surface areas of microporous materials and of total surface area of microporous/mesoporous materials. Mechanical mixtures of mesoporous MCM-41 and microporous FAU-Y powders of known surface areas were used to calculate the respective surface areas by weighted linear combination and the results were compared to the values obtained by the t-plot method. The first slope of the t-plot determined the mesopore and external surface areas ( Smes+ext). The linear fit of the first slope is in general in the range 0.01 < p/ p0 < 0.17 and contains the volumes and relative pressures at which all micropores are filled ( p/ p0 > 0.10). Overestimation of Smes+ext values was evident and appropriate corrections were provided. External surface areas ( Sext) were obtained from the second slope of the t-plot, without noting an overestimation of Sext, thus allowing the determination of mesopore surface areas ( Smes) by difference. Micropore surface areas were calculated by subtracting Smes+ext from the total surface area, SBET. As an example, this methodology was applied to characterize a family of hierarchical microporous/mesoporous FAU-Y (FAUmes) synthesized from H-FAU-Y (H-Y, Si/Al = 15) using C18TAB as the surfactant and different NaOH/Si ratios (0.05 < NaOH/Si < 0.25). By increasing the NaOH/Si ratio in the synthesis of FAUmes, it was shown that as the micropore surface area decreases, the mesopore surface area increases, whereas the micropore and mesopore surface area remains constant. This methodology allows accurate characterization of the surface areas of microporous/mesoporous materials.

Methods Influence in Surface Area Result from Polyurethane Used as Support Media

How Reproducible are Surface Areas Calculated from the BET Equation?

How Reproducible Are Surface Areas Calculated from the BET Equation? (adv. Mater. 27/2022)

Surface Area Determination of Porous Materials Using the Brunauer–Emmett–Teller (BET) Method: Limitations and Improvements

Specific Surface Area Determination for Microporous/Mesoporous Materials: The Case of Mesoporous FAU-Y Zeolites

Determining the Geometric Surface Area of Mesoporous Materials

A new method for calculating the specific surface area of porous metal foams

Evaluation of bacterial diversity recovered from petroleum samples using different physical matrices

Biosurfactant by Serratia sp. BR13816: Fermentation Optimization and Nanoemulsion Formation

Monitoring of Wild Pseudomonas Biofilm Strain Conditions Using Statistical Characterisation of Scanning Electron Microscopy Images

Interlaboratory study for the evaluation of three microtiter plate-based biofilm quantification methods

Modelling and impact of tensiometer plate geometry and sample volume on biosurfactant surface activity assessment

Comparison of quantification methods for an endoscope lumen biofilm model

Relevance of surface characteristics in the adhesiveness of polymicrobial biofilms to crown restoration materials

Evaluation of the BET Theory for the Characterization of Meso and Microporous MOFs

The bet method of analysis of gas adsorption data and its relevance to the calculation of surface areas

A Method for Measuring the Surface Free Energy of Topical Semi-solid Dosage Forms

Using Micro-Patterned Surfaces to Inhibit Settlement and Biofilm Formation by Bacillus Subtilis

Study on Biofilm's Spatial Distribution and Effects on Permeability in Porous Media

Assessing Antimicrobial Efficacy on Plastics and Other Non-Porous Surfaces: A Closer Look at Studies Using the ISO 22196:2011 Standard