Abstract:A methodology for determining the micropore, mesopore, and external surface areas of hierarchical microporous/mesoporous materials from N2 adsorption isotherms at 77 K is described. For FAU-Y zeolites, the microporous surface area calculated using the Rouquerol criterion and the Brunauer-Emmett-Teller (BET) equation is in accord with the geometrical surface determined by the chord length distribution method. Therefore, BET surface area ( SBET) is the well representative of micropore surface areas of microporous materials and of total surface area of microporous/mesoporous materials. Mechanical mixtures of mesoporous MCM-41 and microporous FAU-Y powders of known surface areas were used to calculate the respective surface areas by weighted linear combination and the results were compared to the values obtained by the t-plot method. The first slope of the t-plot determined the mesopore and external surface areas ( Smes+ext). The linear fit of the first slope is in general in the range 0.01 < p/ p0 < 0.17 and contains the volumes and relative pressures at which all micropores are filled ( p/ p0 > 0.10). Overestimation of Smes+ext values was evident and appropriate corrections were provided. External surface areas ( Sext) were obtained from the second slope of the t-plot, without noting an overestimation of Sext, thus allowing the determination of mesopore surface areas ( Smes) by difference. Micropore surface areas were calculated by subtracting Smes+ext from the total surface area, SBET. As an example, this methodology was applied to characterize a family of hierarchical microporous/mesoporous FAU-Y (FAUmes) synthesized from H-FAU-Y (H-Y, Si/Al = 15) using C18TAB as the surfactant and different NaOH/Si ratios (0.05 < NaOH/Si < 0.25). By increasing the NaOH/Si ratio in the synthesis of FAUmes, it was shown that as the micropore surface area decreases, the mesopore surface area increases, whereas the micropore and mesopore surface area remains constant. This methodology allows accurate characterization of the surface areas of microporous/mesoporous materials.

The bet method of analysis of gas adsorption data and its relevance to the calculation of surface areas

Determination of specific surface by the BET method

Is the bet equation applicable to microporous adsorbents?

How Reproducible are Surface Areas Calculated from the BET Equation?

Experimental methods in chemical engineering: specific surface area and pore size distribution measurements—BET, BJH, and DFT

Determining the Geometric Surface Area of Mesoporous Materials

Evaluation of the BET Method for Determining Surface Areas of MOFs and Zeolites that Contain Ultra-Micropores

How Reproducible Are Surface Areas Calculated from the BET Equation? (adv. Mater. 27/2022)

Evaluation of the BET Theory for the Characterization of Meso and Microporous MOFs

Surface Area Determination of Porous Materials Using the Brunauer–Emmett–Teller (BET) Method: Limitations and Improvements

A preliminary study on assessing the Brunauer-Emmett-Teller analysis for disordered carbonaceous materials

The use of nitrogen adsorption for the characterisation of porous materials

Unveiling the Non-Equilibrium Process in Multilayer Mixture Adsorption

Improvement to the Fractal Adsorption Isotherms of Porous Surfaces

Nitrogen adsorption on silica surfaces of nonporous and mesoporous materials

Specific Surface Area Determination for Microporous/Mesoporous Materials: The Case of Mesoporous FAU-Y Zeolites

Surface areas and adsorption energies of biochars estimated from nitrogen and water vapour adsorption isotherms

On the BET Surface Area of Nanocellulose Determined Using Volumetric, Gravimetric and Chromatographic Adsorption Methods

Determination of surface properties and adsorption states of nanoporous materials by Zeta adsorption isotherm

Direct Multilayer Adsorption of Vapor in Solids with Multiscale Porosity and Hindered Adsorbed Layers in Nanopores