Abstract:Wire-based laser directed energy deposition (LDED) technology is an attractive and efficient additive manufacturing technology, which shows great potential in the process of manufacturing high-value engineering components. However, the thermal effect will lead to a large amount of residual tensile stress in the components, and the large crystal structures after solidification seriously affects the tensile performance. The pursuit of high mechanical properties in additive manufacturing components have prompted researchers to seek new strengthening process to produce high-strength components. Therefore, in this paper, laser shock peening (LSP) composite wire-based LDED were used for the additive manufacturing of 17-4 PH stainless steel under the specified experimental conditions, and the effects of LSP on microstructure evolution, microhardness, and tensile properties of wire-based LDED components were systematically studied. Results showed that uniform grains with an average size of 2.31 mu m were generated on the top surface of specimen due to the ultra-high plastic strain induced by LSP shock wave. The size of hierarchical martensitic units shows varying degrees of reduction after LSP treatment, which is shown by the width decrease of packet, block and lath. Dynamic recrystallization caused by rearrangement and annihilation of high-density dislocations promoted the grain refinement. Meanwhile, the residual stress was completely converted from tensile state into compressive state with a maximum value of 425 MPa, and the microhardness was also enhanced to a peak value of 432 HV. In addition, we observed that the high-density dislocation environment created by LSP treatment promoted the further precipitation, and the aggregation phenomenon of precipitates was observed in the dense dislocation area. Furthermore, the tensile strength and elongation of LSP treated specimen were improved significantly, which was attributed to the combined effects of grain refinement, introduction of dislocation structures, precipitation strengthening and gradient residual compressive stress. In summary, laser hybrid additive manufacturing technology provides a new idea and method for the production of high-performance precipitation hardening stainless steel components.

Microstructure and mechanical properties of high-efficiency laser-directed energy deposited 15-5PH stainless steel

Fracture Behavior of PH 15-5 Stainless Steel Manufactured via Directed Energy Deposition

Tensile Properties and Microstructural Evolution of 17–4 PH Stainless Steel Fabricated by Laser Hybrid Additive Manufacturing Technology

Implementation of different scanning strategy to improve the mechanical and wear properties of 15-5 PH stainless steel fabricated by laser-directed energy deposition

Effect of Heat Treatment on Microstructure and Performances of Additively Manufactured 15-5PH Stainless Steel

Microstructure and fracture behavior of 90W-7Ni-3Fe alloy fabricated by laser directed energy deposition

Improving mechanical properties and isotropy of laser DED 17-4 PH stainless steel by combining ultrasonic vibration

Improving the fatigue property of 316L stainless steel through direct energy deposition technology

Enhancement in hardness and corrosion resistance of directed energy deposited 17-4 PH martensitic stainless steel via heat treatment

Improved mechanical properties of laser-repaired 15-5PH stainless steel by in-situ heat treatment and grain refinement

A new laser remelting strategy for direct energy deposition of 316L stainless steel

Heat Treatment-Induced Microstructural Transformations and Strengthening Mechanisms in Laser Powder Bed Fusioned 15-5PH Stainless Steel

Achieving high hardness and wear resistance in phase transition reinforced DC53 die steel by laser additive manufacturing

Microstructures and Mechanical Properties of Laser-Directed Energy Deposited CrCoNi Medium-Entropy Alloy

Microstructural evolution and tensile property enhancement of remanufactured Ti6Al4V using hybrid manufacturing of laser directed energy deposition with laser shock peening

Comparison on Microstructure and Properties of Stainless Steel Layer Formed by Extreme High-Speed and Conventional Laser Melting Deposition

Fatigue Strength Improvement of Laser-Directed Energy Deposition 316L Stainless Steel with In Situ Ultrasonic Rolling by Preliminary Investigation

Additive manufacturing of high-performance 15-5PH stainless steel matrix composites

Influence of laser metal deposition process parameters on a precipitation hardening stainless steel

Directed energy deposition additive manufacturing of a Sc/Zr-modified Al–Mg alloy: Effect of thermal history on microstructural evolution and mechanical properties

Laser Additively Manufactured Intensive Dual-Phase Steels and Their Microstructures, Properties and Corrosion Resistance