Abstract:With the development of unconventional oil and gas resources, the multi-stage fracturing technology with immovable string has been developed rapidly due to its advantages of large construction capacity and multiple fracturing stages. But the failure of packer has become a bottleneck restricting the development of technology. In this paper, the mechanical properties of corroded ((under the environment of I(North Troyes),II(Jeannajor) and III(Khasib)) ) and uncorroded rubber of the packer were tested by designed experiments at first. The experimental values showed that elastic modulus, shear strength and tensile strength decreased when packers were corroded. Then, according to packers' structure and load characteristics, taking the rubber cylinder, rubber support, center pipe, tubing and string as research object, the dynamic model was established for tubes and packers in fracturing layers. Based on conditions of the shear strength, pressure seal and axial movement for rubber cylinder, the safety evaluation method was proposed for packer sealing system. And the failure evaluation of multistage fracturing packer in Gao182-151 well in Daqing Field was carried out by the method established in this paper. At last, we could get the following results: the sealing safety coefficients of upper and lower packers were all greater than 1.0 during the fracturing process of layer I to IV. The axial displacement of the packer's rubber of the non-corrosive and corrosivewere all 0.00. So the packers were sealed well in each stage of fracturing, and no leakage accidents occurred during the entire fracturing process of Gao 182-151 Well. But in the fracturing layer I, the shear safety factor of the corroded (under corrosive environment of I(North Troyes),II(Jeannajor) and III(Khasib)) rubber were is 1.00, 1.10, 0.99 respectively. The shear strength was less than or equal to 1.10 and it didn't not satisfy the shear strength. Therefore, we could get the conclusion that the corroded rubber did not meet the shear strength and rubber tearing was prone to occur in the fracturing layer I. So it is recommended to replace the rubber with a new one before the construction of Gao 182-151Well.

Dynamic calculation of stress influence law of rubber core sealing surface of the rotating blowout preventer with defects

Mechanical Model and Design Method of Rubber Bearing in Prestressed Reticulated Shells

Study on the sealing performance of 105MPa conical core BOP in the fully sealed state

Nonlinear finite element analysis on the sealing performance of rubber packer for hydraulic fracturing

Investigation of Static and Dynamic Seal Performances of a Rubber O-Ring

Finite Element Analysis of Reciprocating Sealing Component of Radial Single-piston Pump

A Visco-hyperelastic Constitutive Model for Rubber Considering the Strain Level and One Case Study in the Sealing Packer

Extrusion, Slide, and Rupture of an Elastomeric Seal

Effect of Swelling Behavior of Rubber Rings on the Sealing Performance for 70MPA Hydrogen Pressure Reducing Valves

Mechanical Behavior and Structure Optimization of Compressed PHP Packer Rubber

How to Use Expansion Rubber to Form an Adaptive Sealing Layer to Solve Severe Loss——Materials, Effects and Theory

Dynamic failure analysis of static seals under pressure fluctuation in an ultrahigh-pressure water piston pump

Failure evaluations for packers in multistage fracturing technology with immobile strings

Analysis on Sealing Performance for a New Type of Rubber Olecranon-Shaped Sealing Ring in Pipe Jacking Joint

Adaptability of hydraulic fracturing packers and optimization of their sealing performance for three common clastic rock reservoirs based on finite element analysis

On the possibility of using simulation modeling for research and design of universal preventer seals

Sealing Failure Analysis on V-Shaped Sealing Rings of an Inserted Sealing Tool Used for Multistage Fracturing Processes

The Change of Sealing Property in the Aging Process of NBR Sealing Equipment Based on Finite Element Analysis

Recent insights into hydrogen-induced blister fracture of rubber sealing materials: An in-depth examination

Stress Analysis and Sealing Capability Research of Rubber Sealing O-Ring for Static Sealing

Mechanical and diffusion property and multi-objective optimization of rubber seals exposed to high-pressure hydrogen gas