Abstract:The stress relaxation of ethylene propylene diene monomer (EPDM) rubber material in a compressed state significantly increases the risk of water leakage at tunnel precast segmental joints. Additionally, EPDM rubber gaskets typically experience a complex precompression strain state, further complicating the prediction of long-term stress relaxation. Therefore, it is imperative to propose a novel constitutive model that realistically reflects the stress relaxation of rubber with arbitrary precompression strain, providing a reference for the long-term waterproof design of shield tunnels. In this study, the time-varying properties of EPDM rubber at material level were studied in detail. At first, a comprehensive set of accelerated aging tests were conducted on EPDM rubber samples with varying precompression strains. The hardening effect of rubber without precompression and the stress relaxation effect of rubber with precompression were explored. The time-varying law and mechanism governing rubber properties under these two effects were analyzed. Subsequently, a conversion relationship between the EPDM rubber test conditions and the actual service time was established. The predicted hardening coefficient for uncompressed EPDM after 100 years is 1.468, whereas the relaxation coefficient for compressed EPDM is 0.359. Comparative analysis revealed that the compression set index do not consider the beneficial effects of hardening, resulting in a 54.1% overestimation of the design water pressure. Finally, the analytical study on the constitutive model of EPDM rubber material was carried out. The error in compression curve for unaged sample obtained from empirical formulas exceeded three times that of the analytical model, underscoring the need to study time-varying constitutive models. An interpolation method was employed to extend the test curve, leading to the development of a new constitutive model that represents the stress relaxation characteristics of EPDM materials under arbitrary precompression strain states. By combining the proposed constitutive model with the timetemperature conversion relationship, the time-varying expressions of the constitutive parameters for relaxation and hardening effects during the service life were derived. In comparison with existing models, the proposed model demonstrates wider applicability, effectively captures the time-varying characteristics of EPDM materials under arbitrary precompression strains, offering an efficient approach for studying the long-term stress relaxation prediction of rubber gaskets in shield tunnels under complex precompression strain states.

A Visco-hyperelastic Constitutive Model for Rubber Considering the Strain Level and One Case Study in the Sealing Packer

Experimental Characterization and Finite Element Modeling the Deformation Behavior of Rubbers with Geometry Defects

A novel viscoelastroplastic constitutive model of rubber materials and parameter identification

Effect of Swelling Behavior of Rubber Rings on the Sealing Performance for 70MPA Hydrogen Pressure Reducing Valves

Visco-Hyperelastic Constitutive Modeling for High-Damping Rubber Materials During Combined Quasi-Static Compression–Cyclic Shear Deformation Process

Establishment of Constitutive Model and Simulation Study on Sealing Performance of Special-Shaped Rubber Cylinder for Inner Packer in Deepwater Pipeline

Hyperelastic Behavior of Two Rubber Materials under Quasistatic and Dynamic Compressive Loadings - Testing, Modeling and Application

The Influence of Rubber Material on Sealing Performance of Packing Element in Compression Packer

Constitutive model and its application for rubber material based on Exp-ln model and generalized viscoelastic theory

A Viscohyperelastic Constitutive Model for Rubber Used in Vibration Isolation

A Nonlinear Hyper-Viscoelastic Constitutive Model for Rubber Material with Finite Strain

Construction of a Rubber Superelastic-Viscoelastic Model and Analysis of Dynamic Response of Structure

Modeling Method of Constitutive Law of Rubber Hyperelasticity Based on Finite Element Simulations

Nonlinear finite element analysis on the sealing performance of rubber packer for hydraulic fracturing

Mechanical Response of the Sealing Packer Based on Two Rubber Materials at High Temperatures

Time-varying Compressive Properties and Constitutive Model of EPDM Rubber Materials for Tunnel Gasketed Joint

Optimization and Experimental Study of the Subsea Retractable Connector Rubber Packer Based on Mooney-Rivlin Constitutive Model

Study on Sealing Performance of Spring-Embedded Shoulder Protection Packer Rubber Cylinder

Research on constitutive models of hydrogenated nitrile butadiene rubber for packer at different temperatures

Effects of Large Deformation and Velocity Impacts on the Mechanical Behavior of Filled Rubber: Microstructure-Based Constitutive Modeling and Mechanical Testing

A visco-hyperelastic constitutive model for EPDM insulation