Abstract:Additive manufacturing is still the fastest-developing technology in the modern world. Three-dimensional printing has become popular due to the method's numerous advantages, such as its short time and low cost, compared to conventional methods such as injection molding. Therefore, the demand for new materials and material systems that will be characterized by the desired functional properties is clearly growing. As part of this work, work was carried out on the development and preparation of new polymer composites dedicated to 3D printing applications, especially in FDM/FFF/MEM technologies. The influence of the content and amount of fillers, such as silica modified with alumina (S) and bentonite modified with a quaternary ammonium salt (B), on the functional properties of a commercially available fiber made of traditional plastic, such as polycarbonate, obtained in the form of a filament (PCF), was determined. It was found that the addition of B significantly increased the fluidity of the polymer, the introduction of a filler in the amount of 1.5% allowed to obtain a result that was 6% higher compared to PCF (16.8 g/10 min), while the amount of 3% was 20% higher. The obtained mass melt flow rate (MFR) results were confirmed by determining the viscosity of the produced polymer composites. Satisfactory results of mechanical properties were obtained, including the following: it was found that the introduced modified fillers increased the elasticity of the material. The introduction of modified silica resulted in a reduction in Young's modulus by 10.02% at the content of 0.5% S and at 1% S by 8.64% compared to the polymer. The introduced modified filler S significantly increased the thermostability of polycarbonate (T5% equal to 449 °C) by 23 °C for PCF/0.5% S and 14 °C for PCF/1% S, respectively. The SEM and WAXS results confirmed the appropriate dispersion of the fillers in the polymer matrix, which indicates well-selected conditions for the homogenization process of the components and the subsequent production of samples. Detailed characterization of the influence of selected fillers on the functional properties of the polymer matrix-polycarbonate allowed for an increase in the range of polymer composites and their use in rapid prototyping technologies, as well as supplementing the literature on databases regarding the characteristics of the obtained materials.

Composite Materials Based on Al2O3 with a Two-Layer Polymer Coating of Ultra-High Molecular Weight Polyethylene and Polyethylene: Synthesis, Properties, and Processing by 3D Printing by Selective Laser Sintering

Modification of Properties of Composites Based on Ultra-High Molecular Weight Polyethylene by Creating Two-Layer Coatings with Low Molecular Weight Polyethylene on Filler Particles: Synthesis, Properties, and Application in 3D Printing by Selective Laser Sintering

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Highly Filled Composite Materials Based on UHMWPE and a Mixture of Micron and Nanoscale Aluminum Particles

A novel printing strategy to fabricate polyetheretherketone (PEEK)-based composites via hollow filaments filled with multiple reinforcements

Aluminium Matrix Composite Materials Reinforced by 3D-Printed Ceramic Preforms

COMPOSITE MIXTURES BASED ON SYNTHETIC POLYMERS AND FILLERS AND EQUIPMENT FOR 3D PRINTING WITH THEM

The Influence of Selected Fillers on the Functional Properties of Polycarbonate Dedicated to 3D Printing Applications

Photopolymerization of ceramic/zeolite reinforced photopolymers: Towards 3D/4D printing and gas adsorption applications

Polymeric composites in extrusion‐based additive manufacturing: a systematic review

Material Extrusion 3D Printing of PEEK-Based Composites

Hybrid of multi‐dimensional fillers for thermally enhanced polyamide 12 composites fabricated by selective laser sintering

High-performance carbon fiber reinforced polyether-ether-ketone composite pellets 3D-Printed via screw-extrusion additive manufacturing

Effect of multidimensional filler hybridization on the mechanical properties of thermoplastic polyurethane composites prepared by selective laser sintering

Investigating the thermal and mechanical properties of novel LDPE/TiO2 and LDPE/TiO2/CNT composites for 3D printing applications

Optimizing the Rheological and Thermal Behavior of Polypropylene-Based Composites for Material Extrusion Additive Manufacturing Processes

PLA/Graphene/MWCNT Composites with Improved Electrical and Thermal Properties Suitable for FDM 3D Printing Applications

Development of 3D printing short carbon fiber reinforced polypropylene composite filaments

Assessment of 3D Printings Produced in Fused Deposition Modeling Printer Using Polylactic Acid/TiO2/Hydroxyapatite Composite Filaments

High-Performance Polymer Blends: Manufacturing of Polyetherimide (PEI)–Polycarbonate (PC)-Based Filaments for 3D Printing

Investigating physical and mechanical properties of alumina/acrylonitrile butadiene styrene composites manufactured by fused deposition modeling