Abstract:The development of new materials is essential for advancing technology and improving the quality of life. With new materials, we can create products that are stronger, more durable, and more efficient. The ongoing research and development of new materials for 3D printing applications continue to drive innovation in various fields, leading to improved products and processes with great benefits. The main goal of this work was to produce a functional filament with a 1.75-mm diameter that may be used for 3D printing. Composite materials were prepared using a low-density polyethylene (LDPE) resin as polymer matrix, and titanium dioxide (TiO2) and carbon nanotubes (CNT) as fillers in various ratios. Up to 15 wt% of TiO2 and 0.25 wt% of CNT were added. Some of the greatest difficulties with high filler content composites are achieving good homogeneity, and in the case of the 3D printing, greatest difficulties are producing the filament with a specific and stable filament diameter. During the 3D printing itself, the fillers can also often cause the nozzle clogging. This paper reports findings of thermal and mechanical properties of the LDPE/TiO2/CNT composites which are significant for the 3D printing process and the applicability of the composite materials. All of the planed composite materials are successfully prepared and 3D printed into the tensile test specimens. The melting point shift caused by the addition of fillers did not show consistent pattern at differential scanning calorimetry, as all of the samples had melting temperatures around 113.5 ± 1.4 °C. The addition of filler, according to the TGA, increased the threshold temperature for the material decomposition, in case of TiO2 5.4 °C increase, while TiO2 and CNT combination increased the threshold temperature for 6.8 °C. The results of the tensile test show a general increase trend with addition of TiO2 filler but do not show to a trend for the tensile strength as a result of the addition of CNT filler. The sample with highest TiO2 filler ratio of 15% (LDPE 15T0C) showed the greatest tensile strength of 14.5 MPa, compared to the 13.0 MPa of pure LDPE. The sample with 5% of TiO2 filler and 0.1% of CNT filler (LDPE 5T0.1C) showed the greatest elongation of 73.9%, compared to the 68.9% of pure LDPE.

Assessment of 3D Printings Produced in Fused Deposition Modeling Printer Using Polylactic Acid/TiO2/Hydroxyapatite Composite Filaments

Experimental investigation of 3D printed polylactic acid and polylactic acid – hydroxyapatite composite through material extrusion technique for biomedical application

Numerical Calculation and Properties Study on Polylactic Acid (Pla)/nano-Hydroxyapatite (N-Ha) Composite Fluid 3D Printed by Fused Deposition Modeling

Properties of poly (lactic Acid)/ hydroxyapatite biocomposites for 3D printing feedstock material

Preparation and performance of poly (vinyl alcohol)/polylactic acid/hydroxyapatite composite scaffolds based on 3D printing

Characterisation and manufacturing methods of material extrusion 3D printing composite filaments based on polylactide and nanohydroxyapatite

3D printed polylactide based zirconia toughened alumina composites: fabrication, mechanical and in vitro evaluation

Physicochemical Properties of 3D-Printed Polylactic Acid/Hydroxyapatite Scaffolds

Fabrication and Characterization of PCL/HA Filament as a 3D Printing Material Using Thermal Extrusion Technology for Bone Tissue Engineering

The Effect of PCL Addition on 3D-Printable PLA/HA Composite Filaments for the Treatment of Bone Defects

The Direct 3D Printing of Functional PEEK/Hydroxyapatite Composites via a Fused Filament Fabrication Approach

Biocompatible Composite Filaments Printable by Fused Deposition Modelling Technique: Selection of Tuning Parameters by Influence of Biogenic Hydroxyapatite and Graphene Nanoplatelets Ratios

Three Dimensional Printing and Biomaterials in the Repairment of Bone Defects; Hydroxyapatite PLA Filaments

Fabrication, mechanical, finite element and In vitro evaluation of 3D printed polylactide/biphasic calcium phosphate composite blends

Mechanical and Wear Characteristics Investigation on 3D Printed Silicon Filled Poly (Lactic Acid) Biopolymer Composite Fabricated by Fused Deposition Modeling

Maximizing performance and efficiency in 3D printing of polylactic acid biomaterials: Unveiling of microstructural morphology, and implications of process parameters and modeling of the mechanical strength, surface roughness, print time, and print energy for fused filament fabricated (FFF) bioparts

The Surface Characterisation of Fused Filament Fabricated (FFF) 3D Printed PEEK/Hydroxyapatite Composites

Investigating the thermal and mechanical properties of novel LDPE/TiO2 and LDPE/TiO2/CNT composites for 3D printing applications

Polylactide (PLA) Filaments a Biobased Solution for Additive Manufacturing: Correlating Rheology and Thermomechanical Properties with Printing Quality

Mechanical properties and shape memory effect of 3D-printed PLA-based porous scaffolds

3D printing of HA / PCL composite tissue engineering scaffolds