Abstract:The PF6− and N‐propyl‐methyl piperidinium (NPMP+) within the CsPbTh3 perovskite film form Lewis acid–base adducts to effectively passivate iodide vacancy defects, regulate crystal growth, and finally uniformly improve grain quality and decrease the trap density. This combinational strategy enables the CsPbTh3 perovskite solar cells to achieve high photovoltaic performance and operational stability. All‐inorganic cesium‐lead‐iodide (CsPbI3Br3−x (2 < x < 3)) perovskite presents preeminent photovoltaic performance and chemical stability. Unfortunately, this kind of material suffers from phase transition to a nonperovskite phase under oxidative chemical stresses. Herein, the introduction of a low concentration of Lewis acid–base adducts (LABAs) is reported to synergistically reduce defect density, optimize interfacial energy alignment, and improve device stability of CsPbI2.75Br0.24Cl0.01 (CsPbTh3) solar cells. Both theoretical simulations and experimental measurements reveal that the noncoordinating anions, PF6−, as a Lewis base can more effectively bind with undercoordinated Pb2+ to passivate iodide vacancy defects than the BF4− and absorbed I−, and thus the point defects are well suppressed. In addition, N‐propyl‐methyl piperidinium (NPMP+) is selected to assemble with PF6− in CsPbTh3 film. The NPMP+ can regulate the crystal growth and finally homogenize the grain size and decrease the trap density. Consequently, the LABAs strategy can improve the power conversion efficiency of CsPbTh3 solar cells to 19.02% under 1‐sun illumination (100 mW cm−2). Fortunately, the NPMP+ and PF6−‐treated CsPbTh3 film shows great phase stability after storage in ambient air for 250 days, and the power conversion efficiency of corresponding solar cells is almost 76% of the initial value after 60 days aging under ambient conditions.

Rational design of Lewis base molecules for stable and efficient inverted perovskite solar cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Stable and Efficient Inverted Perovskite Solar Cells Enabled by Structural Design of Lewis Base Molecules

A Magic Molecular Binder for Stable Efficient Perovskite Solar Cells

Reconstructing Subsurface Lattice for Stable Perovskite Photovoltaics

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Cyclic Multi‐Site Chelation for Efficient and Stable Inverted Perovskite Solar Cells

Lewis Acid–Base Adducts for Efficient and Stable Cesium‐Based Lead Iodide‐Rich Perovskite Solar Cells

Bifunctional Lewis Base‐Assisted Fabrication of High‐Quality CsPbIBr2 Perovskite for Efficient and Stable Solar Cells

Sustainable Molecular Passivation Via Heat-Induced Disaggregation and Redox Reactions for Inverted Perovskite Solar Cells

Bidirectional Targeted Therapy Enables Efficient, Stable, and Eco‐Friendly Perovskite Solar Cells

Highly efficient all-inorganic perovskite solar cells with suppressed non-radiative recombination by a Lewis base

Retarding solid-state reactions enable efficient and stable all-inorganic perovskite solar cells and modules

Covalent Bonding Strategy to Enable Non-Volatile Organic Cation Perovskite for Highly Stable and Efficient Solar Cells

All-in-One Lewis Base for Enhanced Precursor and Device Stability in Highly Efficient Perovskite Solar Cells

Lewis Base Governing Superfacial Proton Behavior of Hybrid Perovskite: Basicity Dependent Passivation Strategy

Promoting Ruddlesden-Popper Perovskite Formation by Tailoring Spacer Intramolecular Interaction for Efficient and Stable Solar Cells

Efficient Liquid‐Solid Coregulation Engineering in Mixed‐cation Lead Mixed‐halide Perovskite for Photovoltaic Performance Improvement

Excess PbI2 Management via Multimode Supramolecular Complex Engineering Enables High‐Performance Perovskite Solar Cells

PbI6 Octahedra Stabilization Strategy Based on π‐π Stacking Small Molecule Toward Highly Efficient and Stable Perovskite Solar Cells

Effective Surface Treatment for Efficient and Stable Inverted Inorganic CsPbI2Br Perovskite Solar Cells