Abstract:Perovskite solar cells (PSCs) have been developed as a promising photovoltaic technology because of their excellent photovoltaic performance. However, interfacial recombination and charge carrier transport losses at the surface greatly limit the performance and stability of PSCs. In this work, the fabrication of high-quality PSCs based on methylammonium lead iodide with excellent ambient stability is reported. An anionic surfactant, sodium dodecylbenzene sulfonate (SDBS), is introduced to simultaneously passivate the defect states and stabilize the cubic phase of the perovskite film. The SDBS located at grain boundaries and the surface of the active layer can effectively passivate under-coordinated lead ions and protect the perovskite components from water-induced degradation. As a result, a champion power conversion efficiency (PCE) of 19.42% is achieved with an open-circuit voltage (VOC) of 1.12 V, a short-circuit current (JSC) of 23.23 mA cm–2, and a fill factor (FF) of 74% in combination with superior moisture stability. The SDBS-passivated devices retain 80% of their initial average PCE after 2112 h of storage under ambient conditions.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14732?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14732</a>.Device fabrication, GIWAXS characterization, device characterization, contact angle measurements, spectroscopy data, SEM data, GIWAXS data, and XRD data (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14732/suppl_file/am0c14732_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Sustainable Molecular Passivation Via Heat-Induced Disaggregation and Redox Reactions for Inverted Perovskite Solar Cells

Suppressing surface and interface recombination to afford efficient and stable inverted perovskite solar cells

Alkyl Chains Tune Molecular Orientations to Enable Dual Passivation in Inverted Perovskite Solar Cells

Ethyl Thioglycolate Assisted Multifunctional Surface Modulation for Efficient and Stable Inverted Perovskite Solar Cells

Bimolecularly passivated interface enables efficient and stable inverted perovskite solar cells

Effective Passivation with Self‐Organized Molecules for Perovskite Photovoltaics

Pyridalthiadiazole‐Based Molecular Chromophores for Defect Passivation Enables High‐Performance Perovskite Solar Cells

Effects of passivated molecular side group on inverted inorganic CsPbI2Br perovskite solar cells

Multiple bonding effects of 1-methanesulfonyl-piperazine on the two-step processed perovskite towards efficient and stable solar cells

Tailoring the mercaptan ligands for high performance inverted perovskite solar cells with efficiency exceeding 21%

Bimolecular Passivation‐Dipole Bridge for Highly Efficient Inverted Perovskite Solar Cells with Low Nonradiative Recombination Loss

Sodium Dodecylbenzene Sulfonate Interface Modification of Methylammonium Lead Iodide for Surface Passivation of Perovskite Solar Cells

In Situ Defect Passivation with Silica Oligomer for Enhanced Performance and Stability of Perovskite Solar Cells

Reformation of thiophene-functionalized phthalocyanine isomers for defect passivation to achieve stable and efficient perovskite solar cells

Perovskite Passivation with a Bifunctional Molecule 1,2‐Benzisothiazolin‐3‐One for Efficient and Stable Planar Solar Cells

Synergistic Interface Layer Optimization and Surface Passivation with Fluorocarbon Molecules toward Efficient and Stable Inverted Planar Perovskite Solar Cells

Fluorinated organic ammonium salt passivation for high-efficiency and stable inverted CsPbI2Br perovskite solar cells

Tailoring Defect Passivation for Efficient and Stable Perovskite Solar Cells via an Ionic Liquid Additive

Air‐Processed Perovskite Solar Cells with >25% Efficiency and High Stability Enabled by Crystallization Modulation and Holistic Passivation

Enhancing Efficiency and Stability of Perovskite Solar Cells via Photosensitive Molecule-Assisted Defect Passivation

Reconfiguration toward Self‐Assembled Monolayer Passivation for High‐Performance Perovskite Solar Cells