Abstract:Concrete-filled steel tubes (CFST) incorporating high-strength steel (HSS) could produce more efficient structural system with lighter weight and higher capacity. However, the design methods for applying concrete-filled highstrength steel tubes (CFHST) are not available yet and limited investigations had been reported. In this research, 8 full scale mid-slenderness circular CFHST specimens, made of innovative high-performance Q460qENH structural steel with actual yielding stress fy as high as 530 MPa, were tested subject to axial and eccentric compression. The main parameters considered in the experimental program included: (a) infilled concrete strength fc' = 39.8-75.3 MPa and (b) loading eccentricity ratio e/D = 0-0.3. The numerical model for CFHST was established and validated with load-displacement curves, failure modes and neutral axis locations obtained from the 8 experiments. The numerical models were further validated in capacity predictions with 232 axial compressions and compression-bending CFHST experimental data collected from the literature, proved to be generally applicable with fy = 435-835 MPa, xi = 0.5-8.5 and lambda n = 0.07-1.90 in both circular and square sections. Based on the validated numerical models, total 526 simulations were performed to investigate the influence of: (a) higher yielding strength fy and thinner-walled steel tubes; (b) confinement factor xi and (c) normalized slenderness ratio lambda n, on the composite strength fsc and compression-bending (N-M) interaction behavior. Experimental and numerical investigations showed that high strength steel could further improve the CFST capacity with basically no reduction in safety margin and ductility performance, but was in need of design method modifications due to changes in composite mechanism. On this basis, an analytical refined plastic-section equilibrium model (RPE model) was proposed to derive practical N-M interaction design curve with consideration of strength enhancement due to the composition and actual stress distribution at ultimate state. The further proposed general design method for compression-bending CFHST included: (a) formulas of fsc-xi relationship; (b) validated formulas of pure-bending capacity and overall stability inherited from GB 50936; (c) practical design curves of N-M interaction considering the effect of xi and lambda n. By comparing with GB 50936, AISC 360, EC 4 and CECS 28 provisions, the proposed method provided more accurate solutions in capacity predictions of CFHST members.

Prediction method for bending moment capacities and failure modes of TSOBs bolted I-beam to hollow section square column

Modeling of Steel Bolted T-Stub Connection under Large Deformation Condition

Load-Carrying Capacity and Practical Calculation Method for Hollow Cylinder Joints Connected with H-Shaped Beams

Load-carrying Capacity and Practical Calculation Method of Welded Hollow Spherical Joints with Square Steel Tubes Subjected to Combined Axial Forces and Biaxial Bending Moments

s Tensile behaviour of T-stub to hollow section column using elliptical-head one-side bolts

Design Of Concrete-Filled Steel Tubular Chs Connections In Tension

Design for local buckling behaviour of welded high strength steel I-sections under bending

Mechanism Analysis and Design of Novel Tapered Iron Bolt Shear Connectors

An Improved and Robust Finite Element Model for Simulation of Thin-Walled Steel Bolted Connections

Analysis of bolted moment connections in cold-formed steel beam–column sub-frames

FEM Analysis on Cyclic Behavior of Improved Beam-Column Connections in Steel Frames

Numerical investigation and design for the local buckling behaviour of high strength steel hexagonal hollow section stub columns under axial compression

Coupled bending-shear-torsion bearing capacity of concrete filled steel tube short columns

Postbuckling Resistance of High Strength Steel Welded I-section Beams Based on Interactive Slenderness

Machine learning (ML) based models for predicting the ultimate bending moment resistance of high strength steel welded I-section beam under bending

Seismic Behavior of a Novel Blind Bolted Flush End-Plate Connection to Strengthened Concrete-Filled Steel Tube Columns

Experimental study and FEM analysis on mechanical behavior of a steel tubular joint with bolted connection subject to biaxial compression

Experimental study of steel beam-column joints with novel slot-bolted connections under a central-column-removal scenario

Finite element analysis and design method for ultra-large capacity end-plate connections

Behavior and General Design Method of Concrete-Filled High-Strength Steel Tube (CFHST) Columns

Finite Element Analysis of the Combined Connection with Bolts and Welds