Abstract:The carbon dioxide reduction reaction (CO2RR) presents the opportunity to consume CO2 and produce desirable products. However, the alkaline conditions required for productive CO2RR result in the bulk of input CO2 being lost to bicarbonate and carbonate. This loss imposes a 25% limit on the conversion of CO2 to multicarbon (C2+) products for systems that use anions as the charge carrier—and overcoming this limit is a challenge of singular importance to the field. Here, we find that cation exchange membranes (CEMs) do not provide the required locally alkaline conditions, and bipolar membranes (BPMs) are unstable, delaminating at the membrane–membrane interface. We develop a permeable CO2 regeneration layer (PCRL) that provides an alkaline environment at the CO2RR catalyst surface and enables local CO2 regeneration. With the PCRL strategy, CO2 crossover is limited to 15% of the amount of CO2 converted into products, in all cases. Low crossover and low flow rate combine to enable a single pass CO2 conversion of 85% (at 100 mA/cm2), with a C2+ faradaic efficiency and full cell voltage comparable to the anion-conducting membrane electrode assembly.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsenergylett.1c01122.Experimental methods; one-dimensional modeling; faradaic efficiency and cell voltage of the AEM MEA; CO2 conversion efficiency with and without carbonate formation in the AEM MEA; current density of a CEM MEA; anode gas CO2 flow with a forward bias BPM MEA; SEM images of the PCRL; structure of a polymer similar to the PCRL; operando ohmic resistance of the PCRL cell; modeled pH at the cathode catalyst; faradaic efficiency of PCRL MEA by loading; PCRL CO2 conversion with varying current densities; gas velocity and Reynolds number of the flow; stability; faradaic efficiency; and current density of the PCRL coating on an Ag catalyst (PDF)This article has not yet been cited by other publications.

High carbon efficiency in CO-to-alcohol electroreduction using a CO reservoir

Efficient electrically powered CO2-to-ethanol via suppression of deoxygenation

Enhanced Electroreduction of CO 2 to Ethanol via Enriched Intermediates under High CO 2 Pressure

Hierarchically Ordered Nanochannel Array Membrane Reactor with Three-Dimensional Electrocatalytic Interfaces for Electrohydrogenation of CO2 to Alcohol

Precise Site-Hydrophobicity Modulation for Boosting High-Performance CO2 Electroreduction

Accelerating electrochemical CO2 reduction to multi-carbon products via asymmetric intermediate binding at confined nanointerfaces

Precise Site-Hydrophobicity Modulation for Boosting High-Performance CO 2 Electroreduction

In-situ Constructed Cu/CuNC Interfaces for Low-Overpotential Reduction of CO2 to Ethanol

Efficient upgrading of CO to C3 fuel using asymmetric C-C coupling active sites

Confined interface engineering of self-supported Cu@N-doped graphene for electrocatalytic CO2 reduction with enhanced selectivity towards ethanol

Single Pass CO 2 Conversion Exceeding 85% in the Electrosynthesis of Multicarbon Products via Local CO 2 Regeneration

Rational catalyst and electrolyte design for CO2 electroreduction towards multicarbon products

Selective Increase in CO2 Electroreduction to Ethanol Activity at Nanograin‐Boundary‐Rich Mixed Cu(I)/Cu(0) Sites via Enriching Co‐Adsorbed CO and Hydroxyl Species

Steering post-C–C coupling selectivity enables high efficiency electroreduction of carbon dioxide to multi-carbon alcohols

Oxygen-Bridged Cu Binuclear Sites for Efficient Electrocatalytic CO2 Reduction to Ethanol at Ultralow Overpotential.

Optimizing Copper Nanoparticles with Carbon Shell for Enhanced Electrochemical CO 2 Reduction to Ethanol

Highly efficient ampere-level CO 2 reduction to multicarbon products via stepwise hollow-fiber penetration electrodes

High-Selectivity Electrochemical Conversion of CO2 to Ethanol using a Copper Nanoparticle/N-Doped Graphene Electrode

Cascade CO2 electroreduction enables efficient carbonate-free production of ethylene

Advanced Catalyst Design and Reactor Configuration Upgrade in Electrochemical Carbon Dioxide Conversion

Carbon‐Efficient CO2 Electrolysis to Ethylene with Nanoporous Hydrophobic Copper