Abstract:The direct electrochemical reduction reaction of carbon dioxide (eCO2RR) captured from the ambient air into base chemicals and fuels holds great potential for an elegant implementation of a net-zero emission carbon cycle. This assumes that the energy used to drive the capturing and conversion process is largely free of carbon dioxide emissions, i.e., from renewables such as wind and photovoltaics. Moreover, high Faradaic efficiency for the desired products at sufficiently high current density in eCO2RR has to be demonstrated to compete with more conventional multi-step Power-to-X conversion schemes both in terms of overall energy efficiency and cost.[1] eCO2RR is known for its wide variety of products.[2] However, hydrogen evolution reaction (HER), which is more thermodynamically reactive, inevitably seizes protons and electrons in the cathode. In addition, the reaction pathway of C2+ products is more complex than that of C1 products because it is strongly dependent on the catalyst surface and electrocatalytic operating conditions. For example, the formation of C-C bonds is interfered with the formation of C-H and C-O bonds on the catalyst surface, resulting in the direct generation of multi-carbon products technically challenging.[3] Due to these kinetic barriers, the C2+ products show much lower the energy efficiency, Faraday efficiency, and partial reduction current density of than those of the C1 products. The mechanistic aspects of the reaction pathways for the various C2+ products have not been fully deciphered, which ultimately limits the commercial application of eCO2RR conversion to C2+ products.[4] Noting that industrial thermocatalytic processes produce and supply long-chain hydrocarbons in a long-term stable manner, we propose the production of C2+ products by combining simultaneous thermocatalysis and electrocatalysis. In the ongoing work, hydrogen from the water electrolysis is further converted to syngas via a reverse water-gas shift reaction (rWGS), followed by an established conversion route to fuels and chemicals such as Fischer-Tropsch or methanol synthesis and methanol to olefins, gasoline or jet fuel.[5] Here, a reactor and test bench capable of operating at 20 bar and 200 degrees Celsius have been fabricated to enable simultaneous thermocatalytic and electrocatalytic production of C2+ products. Furthermore, different catalysts can be employed to explore the catalytic processes on the catalyst surface. References [1] H. Shin, K.U. Hansen, F. Jiao, Techno-economic assessment of low-temperature carbon dioxide electrolysis, Nature Sustainability 4 (2021) 911-919. [2] J. Chen, T. Wang, Z. Li, B. Yang, Q. Zhang, L. Lei, P. Feng, Y. Hou, Recent progress and perspective of electrochemical CO2 reduction towards C2-C5 products over non-precious metal heterogeneous electrocatalysts, Nano Research 14 (2021) 3188-3207. [3] K.D. Yang, C.W. Lee, K. Jin, S.W. Im, K.T. Nam, Current status and bioinspired perspective of electrochemical conversion of co2 to a long-chain hydrocarbon, J Phys Chem Lett 8 (2017) 538-545. [4] Y. Zheng, A. Vasileff, X. Zhou, Y. Jiao, M. Jaroniec, S.Z. Qiao, Understanding the roadmap for electrochemical reduction of co2 to multi-carbon oxygenates and hydrocarbons on copper-based catalysts, J Am Chem Soc 141 (2019) 7646-7659. [5] H. Kirsch, U. Sommer, P. Pfeifer, R. Dittmeyer, Power-to-fuel conversion based on reverse water-gas-shift, Fischer-Tropsch Synthesis and Hydrocracking: Mathematical modeling and simulation in Matlab/Simulink, Chemical Engineering Science 227 (2020) 115930.

Selective and High Current CO 2 Electro-Reduction to Multicarbon Products in Near-Neutral KCl Electrolytes

A Surface Reconstruction Route to High Productivity and Selectivity in CO2 Electroreduction toward C2+ Hydrocarbons

Highly efficient ampere-level CO 2 reduction to multicarbon products via stepwise hollow-fiber penetration electrodes

Hierarchical Copper with Inherent Hydrophobicity Mitigates Electrode Flooding for High-Rate CO 2 Electroreduction to Multicarbon Products

Interface-Enhanced Catalytic Selectivity on the C 2 Products of CO 2 Electroreduction

Enhanced Cuprophilic Interactions in Crystalline Catalysts Facilitate the Highly Selective Electroreduction of CO 2 to CH 4

A Highly Porous Copper Electrocatalyst for Carbon Dioxide Reduction

CO2 electroreduction to multicarbon products in strongly acidic electrolyte via synergistically modulating the local microenvironment

Remodelling the chlor-alkali electrolysis process to co-generate useful reduction products from CO2

Simultaneous Operability of Thermocatalytic and Electrocatalytic CO2 Reduction Reactions

Rational catalyst and electrolyte design for CO2 electroreduction towards multicarbon products

Selective CO2 Electroreduction to Multi-Carbon Products on Organic-Functionalized CuO Nanoparticles by Local Micro-Environment Modulation

Promoting Electrocatalytic Reduction of CO 2 to C 2 H 4 Production by Inhibiting C 2 H 5 OH Desorption from Cu 2 O/C Composite

Selective CO2 electroreduction to multicarbon products exceeding 2 A cm−2 in strong acids via a hollow-fiber Cu penetration electrode

CuC(O) Interfaces Deliver Remarkable Selectivity and Stability for CO2 Reduction to C2+ Products at Industrial Current Density of 500 mA cm−2

Electrolyte Driven Highly Selective CO2 Electroreduction at Low Overpotentials

Selective high-temperature CO2 electrolysis enabled by oxidized carbon intermediates

Conversion of Reactive Carbon Solutions into CO at Low Voltage and High Carbon Efficiency

Enhanced Carbon Monoxide Electroreduction to >1 A cm-2 C2+ Products Using Copper Catalysts Dispersed on MgAl Layered Double Hydroxide Nanosheet House-of-Cards Scaffolds

Direct Low Concentration CO2 Electroreduction to Multicarbon Products Via Rate-Determining Step Tuning

Catalyst electro-redeposition controls morphology and oxidation state for selective carbon dioxide reduction