Abstract:The inspection of thick-section sandwich structures with skins around core materials such as honeycomb, balsa, and foam relies on low-frequency vibration techniques to identify defects through changes in amplitude or phase response. However, current industrial methods are often limited to detecting specific types of defects, potentially overlooking others. Moreover, these methods do not gather detailed information about the defect type or depth, as they only analyse a small portion of the available data instead of the full relevant response spectrum. This paper explores the scientific basis of using low-frequency vibration in the pitch-catch variant for defect detection in homogeneous solids, through analysis of the full relevant frequency spectrum (5–50 kHz). Defects in structures lead to reduced local stiffness and mass in the affected area, causing resonance in the layer above, resulting in amplified vibrations known as local defect resonance (LDR). In this work, an aluminium plate with a 40 mm diameter circular flat-bottomed hole (FBH) at a depth of 1 mm (representing a skin defect) is excited with a chirp signal of 5–50 kHz, and the response is monitored 17 mm away from the excitation point. Finite-element analysis (FEA) is used for the numerical model, addressing challenges in creating an accurate model. The process to optimise the numerical model and the reduce model-experiment error is outlined, including challenges such as the lack of knowledge of material damping. The study emphasizes the importance of modelling the probe's stiffness and damping effects for achieving agreement between the model and experiment. After incorporating these effects, the maximum LDR frequency error decreased from approximately 3 kHz to less than 1 kHz. In addition, this study presents a method with the potential for defect classification through comparison to modelled responses. The minimum difference error was used to quantify the resonance frequencies' error between the model and the experiment. Since the resonant frequencies are a function of the defect's shape, size, and depth, a relatively low root mean squared (RMS) error across the resonance frequency error spectrum indicates the defect's characteristics. Finally, defect detection and sizing using the pitch-catch probe are explored with a wide-band excitation signal and a line scan through the mid-plane of the defect. A method for defect sizing using a pitch-catch probe is presented and experimentally validated. Accurate defect sizing is achieved with the pitch-catch probe when the defect width is at least twice the 17 mm pin-spacing of the probe.

Detection of a Submillimeter Notch-Type Defect at Multiple Orientations by a Lamb Wave A0 Mode at 550 kHz for Long-Range Structural Health Monitoring Applications

An Interdigital Electrode Probe for Detection, Localization and Evaluation of Surface Notch-Type Damage in Metals

Mode conversion of fundamental guided ultrasonic wave modes at part-thickness crack-like defects

Lamb Wave Excitation Using a Flexible Laser Ultrasound Transducer for Structural Health Monitoring

Quantification of Defects in an Aluminum Plate Using Direction-Tunable Shear Horizontal Wave Imaging

Quantitative hidden wall-thinning detection of Lamb waves in aluminium plate with wavenumber analysis

Quantitative Evaluation of Through-Thickness Rectangular Notch in Metal Plates Based on Lamb Waves

Multi-time Lamb waves space wavenumber imaging method based on ultrasonic-guided wavefield

Defect identification in variable thickness waveguides using SH 0 guided wave

Continuous monitoring with a permanently installed high-resolution ultrasonic phased array

Large-area inspection of defects in metal plates using multi-mode guided acoustic waves and sparse sensor networks

Research on Detection of Small Defects of Aluminum Plates Based on Electromagnetic Ultrasonic Lamb Wave

Lamb wave-based damage detection for a channel-like thin-wall structure

Health Monitoring of Stiffened Metallic Plates Using Nonlinear Wave Interaction and Embedded PZT Transducers

Modelling Low-Frequency Vibration and Defect Detection in Homogeneous Plate-Like Solids

Thin Copper Plate Defect Detection Based on Lamb Wave Generated by Pulsed Laser in Combination with Laser Heterodyne Interference Technique

A Flexible Film Magnetostrictive Patch Transducer for Non Dispersive Shear Horizontal Wave Testing

Defect Detection of Aluminium Plates Based on Near-Field Enhancement of Lamb Waves Generated Using an Electromagnetic Acoustic Tranducer.

Structural Health Monitoring System Based on a Concept of Lamb Wave Focusing by the Piezoelectric Array

Experimental Research on Hole-like Defect Detection in Plate Based on Ultrasonic Guided Waves Technique

Lamb Waves and Electro-Mechanical Impedance Based Damage Detection Using a Mobile PZT Transducer Set.