Abstract:The limitation of poor mechanical stability and difficulties in printing electrically conductive components can be overcome owing to the recent introduction of nanotechnology into the field of additive manufacturing (AM) and the consequent development of nonconventional polymer nanocomposites suitable for 3D printing. In the present work, different weight percentages (up to 6 wt % in total) of carbon-based nanostructures-multiwalled carbon nanotubes (MWCNTs), graphene nanoplatelets (GNPs), and a combination of both fillers (MWCNTs/GNPs)-were incorporated into poly(lactic) acid (PLA, Ingeo™) in an attempt to overcome several limitations of conventional 3D manufacturing based on insulating materials. Solution blending and melt mixing were the two fabrication methods adopted for preparation of the samples under test. A comparison of the morphological, rheological, and electrical properties of the resulting nanocomposites was carried out. Moreover, for the same weight concentrations, the influence of physical and geometrical features (i.e., functionalization and aspect ratio) of the embedded fillers was also investigated. Rheological methods were applied to control the quality of fillers dispersion in PLA matrix. The rheological percolation threshold was considered as reference in order to evaluate the internal structure of nanodispersions. TEM visualization, combined with rheological characterizations, was used for efficient control of the nanofiller dispersion. DC characterization revealed that lower electrical percolation thresholds and higher values of electrical conductivity were achieved using fillers with a larger aspect ratio and melt mixing, respectively. Moreover, given the possibility of obtaining complex and appropriate shapes for electromagnetic compatibility (EC) applications, electromagnetic (EM) response of the nanocomposites at the highest filler concentration was investigated in GHz and THz regions. It was found that the electromagnetic shielding efficiency (EMI) of nanocomposites strongly depended on the aspect ratio of the nanofillers, whereas the type of processing technique did not have a significant effect. Therefore, a careful choice of methods and materials must be made to address the final application for which these materials and further 3D printed architectures are designed.

3D Printing of Electrically Conductive Objects with Biobased Polyglycerol Acrylic Monomers

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Fully Bio-Based Polymer Composites: Preparation, Characterization, and LCD 3D Printing

(Meth)acrylate-Free Three-Dimensional Printing of Bio-Derived Photocurable Resins with Terpene- and Itaconic Acid-Derived Poly(ester-thioether)s

Glycerol-based Sustainably Sourced Resin for Volumetric Printing

Three-Dimensional Printing Fully Biobased Heat-Resistant Photoactive Acrylates from Aliphatic Biomass

Improving the 3D Printability and Mechanical Performance of Biorenewable Soybean Oil-Based Photocurable Resins

Morphological, Rheological and Electromagnetic Properties of Nanocarbon/Poly(lactic) Acid for 3D Printing: Solution Blending vs. Melt Mixing

Tailoring Mechanical Properties for Additive Manufacturing: Strategic Molecular Design of UV-Curable Bio-based Oligomeric Polyester Resins via Diacid and Diol Exploration

DLP 3D printing of levoglucosenone‐based monomers: exploiting thiol‐ene chemistry for bio‐based polymeric resins

Tailoring Mechanical Properties for Additive Manufacturing: Strategic Molecular Design of UV-Curable Bio-based Oligoester Resins via Diacid and Diol Exploration

Photocurable Itaconic Acid-Functionalized Star Polycaprolactone in Biobased Formulations for Vat Photopolymerization

Development of recyclable bio-based epoxy/acrylate blends for liquid crystal display 3D printing

Synthesis of Bio-Based Polyester Resins for Vat Photopolymerization 3D Printing

Vat Photopolymerization 3D-Printing of Dynamic Thiol-Acrylate Photopolymers Using Bio-Derived Building Blocks

Renewable Methacrylate Resins for 3D Printing Containing Dynamic Hydroxyester Linkages for Reprocessability

Urethane dimethacrylate-based photopolymerizable resins for stereolithography 3D printing: A physicochemical characterisation and biocompatibility evaluation

Extrusion Based 3D Printing of Sustainable Biocomposites from Biocarbon and Poly(trimethylene terephthalate)

Digital Light Processing to Afford High Resolution and Degradable CO2‐Derived Copolymer Elastomers

Development of Bisphenol-A-Glycidyl-Methacrylate- and Trimethylolpropane-Triacrylate-Based Stereolithography 3D Printing Materials

Digital Light Processing-3D Printing of Thermoset Materials with High Biodegradability from Amino Acid-Derived Acrylamide Monomers