Abstract:In order to reduce current leakage and improve electron transfer in solar cells, charge transport layers (CTL), mainly hybrid electron transport layers (h-ETL), are considered as a solution. In this research contribution, computational analysis using SCAPS-1D software is performed to explore the output photovoltaic parameters of a Sb2S3-based solar cell with h-ETL. No theoretical works on this configuration have been previously reported. The main objectives of the present work are to propose a h-ETL with good band alignment with the Sb2S3 absorber, high transparency, and Cd free; to mitigate the instability and cost issues associated with using Spiro-OMeTAD HTL; and to optimize the solar cell. Thus, we calibrated the J - V characteristics and electrical parameters of the FTO/(ZnO/TiO2)/Sb2S3/Spiro-OMeTAD/Au solar cell by numerical simulation and compared them with those of the experiment. Subsequently, our simulations show that to replace the TiO2 ETL used in the experiment and to form the h-ETL with ZnO, IGZO is found to be a good candidate. It has better band alignment with the Sb2S3 absorber than TiO2 ETL, which reduces the trap states at the ETL/Sb2S3 interface; it has high transparency due to its wide bandgap; and an intense electric field is generated at the IGZO/Sb2S3 interface, which reduces the recombination phenomenon at this interface. MoO3, MASnBr3, Cu2O, CuI, and CuSCN HTL were also tested to replace the Spiro-OMeTAD HTL. Simulation results show that the cell with MoO3 HTL achieves higher performance due to its high hole mobility and high quantum efficiency in the visible region; it also allows the solar cell to have better thermal stability ( TC = − 0.32 %/K) than the cell with Spiro-OMeTAD HTL ( TC = − 0.53 %/K). The parameters that could improve the solar cell efficiency ( η ) obtained after these substitutions were also optimized. In particular, the parameters of the Sb2S3 absorber layer (thickness, defect density, and doping), ETL and HTL layer thicknesses, h-ETL/Sb2S3 interface defect density, and series and shunt resistances have been optimized. Finally, by combining high performance and thermal stability, the results show that the thermal stability of the solar cell depends on the back contact type; thus, nickel (Ni) was found to combine high performance and better thermal stability among the back contacts investigated. After these improvements, the efficiency of the Sb2S3-based solar cell increased from 5.08% ( J SC = 16.19 mA/cm2, V OC = 0.56 V, and FF = 55.40 %) to 15.43% ( J SC = 18.51 mA/cm2, V OC = 1.11 V, and FF = 74.76 %). This study proposes an approach to optimize the Sb2S3 upper subcell for tandem solar cells.

Simulating the Effect of Inserting Sb2S3 as Hole Transport Layer on SnS-Based Thin-Film Solar Cells

Modeling and Simulation of Tin Sulfide (SnS)-Based Solar Cell Using ZnO as Transparent Conductive Oxide (TCO) and NiO as Hole Transport Layer (HTL)

Performance Enhancement of SnS Solar Cell with Tungsten Disulfide Electron Transport Layer and Molybdenum Trioxide Hole Transport Layer

Performance evaluation of WS2 as buffer and Sb2S3 as hole transport layer in CZTS solar cell by numerical simulation

Design and simulation of Cu2SnSe3-based solar cells using various hole transport layer (HTL) for Performance Efficiency above 32%

Effect of Different Device Parameters on Tin Based Perovskite Solar Cell Coupled with In2S3 Electron Transport Layer and CuSCN and Spiro-OMeTAD Alternative Hole Transport Layers for High Efficiency Performance

Utilizing machine learning to enhance performance of thin-film solar cells based on Sb2(S x Se1- x )3: investigating the influence of material properties

Modeling and optimization of numerical studies on CuSbS 2 thin film solar cell with ∼ 15% efficiency

Investigation of the Performance of a Sb2S3-Based Solar Cell with a Hybrid Electron Transport Layer (h-ETL): A Simulation Approach Using SCAPS-1D Software

Concurrent investigation of antimony chalcogenide (Sb2Se3 and Sb2S3)-based solar cells with a potential WS2 electron transport layer

Numerical Simulation of the Performance of Sb2Se3 Solar Cell via Optimizing the Optoelectronic Properties Based SCAPS-1D

Stability and Efficiency Enhancement of Antimony Selenosulfide Solar Cells with Inorganic SnS‐Modified Nickel Oxide Hole Transport Materials

All-Inorganic Hydrothermally Processed Semitransparent Sb 2 S 3 Solar Cells with CuSCN as the Hole Transport Layer

Numerical Investigation of CuSbS2Thin Film Solar Cell using SCAPS-1D: Enhancement of Efficiency on Experimental Films by Defect Studies

SCAPS study on the effect of various hole transport layer on highly efficient 31.86% eco-friendly CZTS based solar cell

Efficient SnS Solar Cells via Plasmonic Light Trapping and Alternative Buffer Layers: A Combined Machine Learning and FDTD Analysis

Impact of hole transport layer on the performance of all-inorganic tin (Sn) based perovskite solar cells

Dopant-free Fluorene Based Dimers linked with Thiophene Units as Prospective Hole Transport Materials for Sb2S3 Solar Cells

Towards high-efficiency planar heterojunction antimony sulfide solar cells

Numerical Simulation of Copper Indium Gallium Diselenide Solar Cell with Ultra-Thin BaSi2 Back Surface Field Layer Using the Non-Toxic In2Se3 Buffer Layer

Stable and efficient Sb2Se3 solar cells with solution-processed NiOx hole-transport layer