Abstract:CoCrFeNi alloy is the most well-known four-component equiatomic alloy. In addition, it has a low-cost composition among HEAs. Four-component alloys are considered semi-HEAs. Therefore, a five-component HEA design was made by adding another metal to the main composition of CoCrFeNi. As the fifth metal, two metals such as Al and Ti, which are relatively low in cost and have the potential to improve properties, were chosen. For this purpose, in this study, the effect of Al and Ti on CoCrFeNi main alloy was investigated by producing three different samples as CoCrFeNi, CoCrFeNiAl, and CoCrFeNiTi. The alloys with three different compositions (used three different samples) were successfully produced by the mechanical alloying method. Although Al and Ti have the possibility of intermetallic with other metals in the alloy, such a formation was not observed during mechanical alloying, and it was observed that all metals were homogeneously distributed in the alloy. The microhardness results indicated that CoCrFeNiAl and CoCrFeNiTi samples had similar hardness values. While the hardness of the CoCrFeNi sample was 136 HV, the hardness of the CoCrFeNiAl sample was 262 HV. However, the hardness of the CoCrFeNiTi sample decreased significantly. The hardness of the CoCrFeNiTi sample was measured as 269 HV. It was observed that the addition of Ti and Al to the base alloy was increased a significant change in hardness. It has been observed that Ti supplementation has a more positive effect on improving corrosion properties. It is seen that the corrosion potentials shift toward more negative potentials with the addition of Al and Ti to the CoCrFeNi (−194 mV) alloy (−306 and −224 mV for CoCrFeNiAl and CoCrFeNiTi, respectively). When the surface morphologies of the alloys are compared after corrosion; the damage to the alloy surfaces increases due to the negative E corr value in CoCrFeNiAl and CoCrFeNiTi alloys compared to the master alloy. However, the high corrosion current density (12.69 μA/cm 2 ) in the CoCrFeNiTi sample caused much more damage to this alloy.

Development of 4- Component Eutectic High Entropy Alloys Using Electromagnetic Levitation Technique

Exploring Zr Influence on Microstructure and Mechanical Property in FeCoNiCrCuZr Eutectic High-Entropy Alloys

Study on the Microstructure and Mechanical Properties of Non-Equimolar NiCoFeAlTi High Entropy Alloy Doped with Trace Elements

Design Multicomponent Eutectic Alloys in the Co–Cr–Fe–Ni–Nb System Using Simple Mixing Method

Microstructure and mechanical properties of non equiatomic FeCoNiCuMo high entropy systems

Production of CoCrFeNi(Al/Ti) High-Entropy Alloys by Mechanical Alloying: Optimization of Milling Time and Comparison of Corrosion Susceptibilities

Controlled Valence Electron Concentration Approach to Tailor the Microstructure and Phase Stability of an Entropy-Enhanced AlCoCrFeNi Alloy

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Microstructure and properties of a novel cost-effective FeNi-based eutectic high entropy alloys

A new approach to determine/design the eutectic composition of binary, ternary, and high-entropy alloys using electromagnetic directional crystallization

SYNTHESIS AND STRUCTURE OF FOUR TiZrVNb AND FIVE-COMPONENT TiZrHfVNb REFRACTORY HIGH-ENTROPY ALLOYS

A Study on the Phase Formation and Magnetic Properties of FeNiCoCuM (M = Mo, Nb) High-Entropy Alloys Processed Through Powder Metallurgy

Design and Development of High-Entropy Alloys with a Tailored Composition and Phase Structure Based on Thermodynamic Parameters and Film Thickness Using a Novel Combinatorial Target

Thermodynamics‐Guided High‐Throughput Discovery of Eutectic High‐Entropy Alloys for Rapid Solidification

Microstructure and mechanical properties variation with Ni content in Al0.8CoCr0.6Fe0.7Nix (x = 1.1, 1.5, 1.8, 2.0) eutectic high-entropy alloy system

Microstructural evolution and phase selection during solidification of AlCrCuFeNi high entropy alloy

Microstructural evolution of CrCuFeNiZn nanocrystalline high entropy alloy prepared by mechanical alloying

Microstructure and mechanical properties of CrFeNiBx eutectic high entropy alloys

Manufacturing of Ni-Co-Fe-Cr-Al-Ti High-Entropy Alloy Using Directed Energy Deposition and Evaluation of Its Microstructure, Tensile Strength, and Microhardness

Designing novel AlCoCrNi eutectic high entropy alloys

Microstructure and elevated-temperature mechanical properties of refractory AlMo0.5NbTa0.5TiZr High Entropy Alloy fabricated by powder metallurgy