Abstract:Composites that use fly ash and slag as alkali-activated materials instead of cement can overcome the defects and negative effects of alkali-activated cementitious materials prepared with the use of an alkali-activated material. In this study, fly ash and slag were used as raw materials to prepare alkali-activated composite cementitious materials. Experimental studies were carried out on the effects of the slag content, activator concentration and curing age on the compressive strength of the composite cementitious materials. The microstructure was characterized using hydration heat, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM), and its intrinsic influence mechanism was revealed. The results show that increasing the curing age improves the degree of polymerization reaction and the composite reaches 77~86% of its 7-day compressive strength after 3 days. Except for the composites with 10% and 30% slag content, which reach 33% and 64%, respectively, of their 28-day compressive strength at 7 days, the remaining composites reach more than 95%. This result indicates that the alkali-activated fly ash–slag composite cementitious material has a rapid hydration reaction in the early stage and a slow hydration reaction in the later stage. The amount of slag is the main influencing factor of the compressive strength of alkali-activated cementitious materials. The compressive strength shows a trend of continuous increase when increasing slag content from 10% to 90%, and the maximum compressive strength reaches 80.26 MPa. The increase in the slag content introduces more Ca2+ into the system, which increases the hydration reaction rate, promotes the formation of more hydration products, refines the pore size distribution of the structure, reduces the porosity, and forms a denser microstructure. Therefore, it improves the mechanical properties of the cementitious material. The compressive strength shows a trend of first increasing and then decreasing when the activator concentration increases from 0.20 to 0.40, and the maximum compressive strength is 61.68 MPa (obtained at 0.30). The increase in the activator concentration improves the alkaline environment of the solution, optimizes the level of the hydration reaction, promotes the formation of more hydration products, and makes the microstructure denser. However, an activator concentration that is too large or too small hinders the hydration reaction and affects the strength development of the cementitious material.

Mechanical properties and mechanisms of alkali-activated slag paste reinforced by graphene oxide-SiO2 composite

Preparation of Coal Gasification Coarse Slag-Based Alkaline Activator and Its Activation Mechanism in Alkali-Activated Slag

Investigation of Graphene Derivatives on Electrical Properties of Alkali Activated Slag Composites

Investigation on fluidity, microstructure, mechanical and durability properties of snail shell-based graphene oxide cement composite material

Study on the Compressive Strength and Reaction Mechanism of Alkali-Activated Geopolymer Materials Using Coal Gangue and Ground Granulated Blast Furnace Slag

Research on rheology performance and sealing effect of alkali-activated GGBS paste used for tunnel leakage plugging

Mechanical properties and hydration behavior of dehydrated cement paste-slag based composite cementitious material

Reactive molecular dynamics and experimental study of graphene-cement composites: Structure, dynamics and reinforcement mechanisms

Alkali-activated slag (AAS) paste: Correlation between durability and microstructural characteristics

Shrinkage mechanisms and shrinkage-mitigating strategies of alkali-activated slag composites: A critical review

Fracture properties and microstructure formation of hardened alkali-activated slag/fly ash pastes

Reinforcing Effects of Graphene Oxide on Portland Cement Paste

Alkali-activated slag mortar molded by non-stirring molding: Compressive strength, hydration properties and microstructures

Study of the Mechanical Properties and Microstructure of Alkali-Activated Fly Ash–Slag Composite Cementitious Materials

Graphene oxide/Al composites with enhanced mechanical properties fabricated by simple electrostatic interaction and powder metallurgy

Effect of Graphite on the Self-Sensing Properties of Cement and Alkali-Activated Fly Ash/slag Based Composite Cementitious Materials

A novel admixture to improve durability of alkali-activated slag by reducing water sorptivity and optimising the process of activation

Reinforcing Mechanism Of Graphene And Graphene Oxide Sheets On Cement-Based Materials

Rheological Behavior of Fresh Cement Composites with Graphene Oxide–Coated Silica Fume

Reinforcing mechanisms review of the graphene oxide on cement composites

Molecular dynamics simulation and experimental study on mechanical properties and microstructure of cement-based composites enhanced by graphene oxide and graphene