Abstract:Lithium-sulfur (Li-S) batteries are a promising candidate for next-generation energy storage owing to the high theoretical capacity of sulfur (1,675 mAh g −1 ). However, the intrinsically low electrical conductivity of sulfur and complex multistep electrolyte-mediated redox reactions involving soluble lithium polysulfide intermediates engender critical challenges toward practical realization. Specifically, migration and diffusion of higher-order lithium polysulfides provokes continuous loss of active sulfur species, yielding premature capacity fade. Electrochemical kinetics also remain sluggish due to the insulating nature of sulfur cathodes, which require engineering designs to accelerate charge transfer. Rational morphological and compositional cathode tuning represents a compelling strategy for addressing fundamental Li-S limitations. Herein, we develop an extended cathode architecture composed of a porous carbon nanotube network decorated with homogenously dispersed nanocatalysts. Electron microscopy and spectroscopy analysis verify platinum group metals are well-incorporated both within internal channels and external surface sites of conductive carbon nanotubes. The composite framework affords multifaceted functionality arising from synergistic chemical and structural attributes of components. Nanocatalyst sites demonstrate a pronounced chemical affinity toward soluble polysulfide intermediates, effectively localizing them within cathode, minimizing diffusional losses toward the anode. This anchoring phenomenon is complemented by the inherent microporosity of the high-surface-area nanotube network, further obstructing polysulfide migration through a confinement effects. Concurrently, noble metal nanoparticles facilitate the redox conversion of trapped higher-order polysulfides into solid Li 2 S alleviating the precipitation of electrically insulating discharge products. The excellent electrical conductivity of CNTs ensures efficient charge transport to all incorporated sulfur active materials, further maximizing reversible utilization. As a result of complementary polysulfide confinement and electrocatalytic conversion functionalities, Li-S coin cells exhibit enhanced reversible capacities exceeding 900 mAh g −1 for over 500 cycles at 0.558 A g −1 . Notably, over 500 cycles, minimal capacity decay of 0.018% per cycle and 92% retention of the initial capacity are obtained at moderate sulfur loadings highlighting the exceptional cycling stability enabled by engineered cathodes. Outstanding rate performance is also demonstrated with the delivery of 854 mAh g −1 capacity at a very high current density of 1.675 A g −1 . Our rationally designed cathode architecture provides critical mechanistic insight toward addressing fundamental bottlenecks to progress Li-S technologies.

Scalable SPAN Membrane Cathode with High Conductivity and Hierarchically Porous Framework for Enhanced Ion Transfer and Cycling Stability in Li–S Batteries

Flexible CNT-Interpenetrating Hierarchically Porous Sulfurized Polyacrylonitrile (CIHP-SPAN) Electrodes for High-Rate Lithium-Sulfur (Li-S) Batteries

Integrated Configuration Design Strategy Via Cathode‐Gel Electrolyte With Forged Solid Electrolyte Interface Toward Advanced Lithium‐Sulfurized Polyacrylonitrile Batteries

Tailored Electrolytes Enabling Practical Lithium–Sulfur Full Batteries Via Interfacial Protection

Three-dimensional Spongy Framework As Superlyophilic, Strongly Absorbing, and Electrocatalytic Polysulfide Reservoir Layer for High-Rate and Long-Cycling Lithium-Sulfur Batteries

Enhancing the performance of a lithium-sulfur battery with spatially confined mesoporous nanoreactors in sulfurized polyacrylonitrile cathodes

Constructing 1D/2D Interwoven Carbonous Matrix to Enable High-Efficiency Sulfur Immobilization in Li-S Battery

Charge/discharge Characteristics of Sulfurized Polyacrylonitrile Composite with Different Sulfur Content in Carbonate Based Electrolyte for Lithium Batteries

Selenium-Doped Sulfurized Poly(acrylonitrile) Composites as Ultrastable and High-Volumetric-Capacity Cathodes for Lithium–Sulfur Batteries

Synergistic Electrocatalyst-Cathode Architecture for Stable Long-Term Cycling Lithium-Sulfur Batteries

Understanding the Roles of the Electrode/Electrolyte Interface for Enabling Stable Li∥Sulfurized Polyacrylonitrile Batteries.

Facile synthesis of sulfurized polyacrylonitrile composite as cathode for high-rate lithium-sulfur batteries

3D-Hybrid Material Design with Electron/lithium-Ion Dual-Conductivity for High-Performance Li-sulfur Batteries

Strategy for High-Energy Li-S Battery Coupling with a Li Metal Anode and a Sulfurized Polyacrylonitrile Cathode

Low-Cost Li||SPAN Batteries Enabled by Sustained Additive Release

Multilevel structured carbon film as cathode host for Li-S batteries with superhigh-areal-capacity

Feasible Catalytic-Insoluble Strategy Enabled by Sulfurized Polyacrylonitrile with In Situ Built Electrocatalysts for Ultrastable Lithium–Sulfur Batteries

Free-standing Sulfur Cathodes Composited with Carbon Nanorods Arrays for Li-S Batteries Application

Unraveling the mechanism on improved kinetics performance of sulfurized polyacrylonitrile with defective conductive carbon matrix

Immobilization and Catalytic Conversion of Polysulfide by In-Situ Generated Nickel in Hollow Carbon Fibers for High-Rate Lithium-Sulfur Batteries

SPAN secondary particles enabled high energy density Lithium-Sulfur battery