Abstract:As part of the LEAP (Liquefaction Experiments and Analysis Projects), many centrifuge model tests on a sheet pile retaining wall were conducted at six different centrifuge facilities around the world. Each centrifuge facility used containers of different W/H (width of container/height of wall) ratios to model the same plane strain prototype retaining wall. Predictions of the centrifuge tests that neglected wall friction, assumed plane strain conditions, and used the CycLiq constitutive model, exhibit reasonable general agreement with tests in terms of liquefaction response. However, an overprediction of the median response of sheet pile wall displacement was observed. The study presented in this paper was motivated by a concern that friction on the side walls might be biasing results from model containers with different W/H. A numerical simulation parametric study using FLAC3D is presented to illustrate the potential effects of interface friction and container geometry on the LEAP retaining wall test results. The results show that incorporation of appropriate container geometry and soil-container friction can reduce the error between simulated and experimental sheet pile wall displacements. Soil-container friction is also shown to affect the total earth pressure and especially its distribution on the sheet pile wall, causing the actual tests to deviate from the intended plane strain conditions. For the assessed liquefaction related cases, soil-container friction has the additional effect of significantly restricting the local development of excess pore pressure and subsequent soil deformation, further contributing to its influence on the centrifuge tests. The parametric study indicates that an interface friction angle of 17.6° and W/H>1, 2, and 3 reduced horizontal wall displacements by 50%, 20%, and 10% respectively, compared to simulations neglecting wall friction. Use of containers with large W/H is therefore recommended for future centrifuge experiments.

Liquefaction in the presence of soil-structure interaction: Centrifuge tests of a sheet-pile quay wall in LEAP-2020

Large Deformation Finite-Element Simulation of Displacement-Pile Installation Experiments in Sand

Large-Deformation Finite-Element Simulation of Deformation and Strain Fields Resulting from Closed-End Displacement Pile Installation in Sand

Centrifuge Modeling of Monotonic and Cyclic Lateral Behavior of Monopiles in Sand

Wave-induced Liquefaction of the Seabed Around a Single Pile Considering Pile–soil Interaction

Modeling cyclic liquefaction and system response of a sheet-pile supported liquefiable deposit: Insights from LEAP-2022

Assessment of soil constitutive models for predicting seismic response of sheet pile walls: A LEAP-2022 project study

Liquefaction and fluidization responses of level ground retained by sheet-pile wall through centrifuge model tests

Influence of Centrifuge Test Soil-Container Friction on Seismic Sheet-Pile Wall Response in Liquefiable Deposit: Insights from Numerical Simulations

Stress-strain response of the LEAP-2015 centrifuge tests and numerical predictions

Numerical analysis of LEAP centrifuge tests on sloping liquefiable ground: Influence of dilatancy and post-liquefaction shear deformation

LEAP centrifuge tests on retaining walls at Cambridge University

Predictions of seismic response for sheet-pile wall in liquefiable deposit within LEAP 2022 using the CycLiq constitutive model

LEAP-ASIA-2019: Validation of centrifuge experiments and the generalized scaling law on liquefaction-induced lateral spreading

Liquefaction Experiment and Analysis Projects (LEAP): Summary of Observations from the Planning Phase

Numerical Modelling of Liquefaction in Loose Sand Deposits Subjected to Ocean Waves

Liquefaction-induced lateral load on pile group of wharf system in a sloping stratum: A centrifuge shake-table investigation

Shear Wave Velocity-Based Evaluation of Cyclic Mobility Type of Liquefaction and Validation by Centrifuge Model Tests in LEAP

Lateral Spreading Near Deep Foundations and Influence of Soil Permeability

Estimation of Bending Moment and Pile Displacement for Soil-Pile-quay Wall System Subjected to Liquefaction Induced Lateral Spreading

Zhejiang University Benchmark Centrifuge Test for LEAP-GWU-2015 and Liquefaction Responses of a Sloping Ground