Abstract:This study aims to examine the 50/50 polypropylene/polyamide 6 (iPP/PA6) system molded under confined flow conditions, both in its original state and after being modified by two different interfacial agents. This study provides two main insights. Firstly, it focuses on a polymer blend close to phase inversion. Secondly, it investigates the impact of using two different types of interfacial agents (derived from polymer waste) to enhance the compatibility between iPP and PA6. Dynamic Mechanical Analysis (DMA) has been employed to achieve these objectives. It is important to note that the investigation of the 50/50 iPP/PA6 system is a crucial focus predicted in previous studies, where a series of mechanical properties were evaluated using Box–Wilson design of experiments (DOEs) over the whole compositional range on the iPP/PA6 binary system. Thus, two interfacial modifiers, namely succinic anhydride (SA)-grafted atactic polypropylene with terminal, side, and bridge SA grafts (aPP-SASA) and succinyl-fluoresceine (SF) with bridge succinic anhydride grafting atactic polypropylene (aPP-SFSA), were employed. The authors obtained and characterized these agents. The quantity of these agents used in the blend was identified as a critical coordinate in prior studies conducted by the authors. The processing method used, compression molding under confined conditions, was chosen to minimize any orientation effect on the emerging morphology. All characterization procedures were performed on samples processed by contour machining to retain the blend morphologies as they emerged from the processing stage. Results from WAXS and SAXS synchrotron tests concluded there were no changes in the crystal morphology of the iPP or the PA6 in the blends nor any co-crystallization process throughout the compositional range. These findings, and the long period fits on the PP crystalline phase for the fifty/fifty blends we are discussing, will support the present DMA study. Finally, the efficiency of these interfacial modifiers has been concluded, even in this unfavorable scenario.

Interface Physical Influence on Mechanic Properties of PP/AS Modified Polymer Caused by Maleic Anhydride

Regulation of Structure and Mechanical Properties of Poly(propylene-Butene) Alloys by Monomer Composition Switching

Simultaneous Graft Polymerization of Polypropylene with Maleic Anhydride and Butyl Acrylate

Combination of double-modified clay and polypropylene-graft-maleic anhydride for the simultaneously improved thermal and mechanical properties of polypropylene

Enhancing Mechanical Performance of High-Lignin-Filled Polypropylene via Reactive Extrusion

Effect of Maleic‐anhydride‐grafted Polypropylene As a Compatibilizer on the Properties of Polypropylene/(modified Carbon Black) Composites

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Mechanical Properties and Morphology of Polypropylene/Polypropylene-g-Maleic Anhydride/Long Glass Fiber Composites

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Effects of Calcium Carbonate and Compounding Sequence on the Phase Morphology and Properties of Maleic Anhydride-Grafted Polypropylene Compatibilized Polyamide 6/polypropylene Blend

Enhanced Mechanical Properties of Polylactic Acid/Poly(Butylene Adipate-co-Terephthalate) Modified with Maleic Anhydride

The effect of addition of poly(propylene-g-acrylic acid) on the morphology of poly(vinyl methylether) and isotactic polypropylene blend

A Dynamic Mechanical Analysis on the Compatibilization Effect of Two Different Polymer Waste-Based Compatibilizers in the Fifty/Fifty Polypropylene/Polyamide 6 Blend

Compatibilizing Modification and Mechanism of PP/WF Composites

Compatibilization Effect of PP-g-(MAH/VAc) on Polypropylene/Polyamide 6 Blends

Preparation, structure and properties of dynamically vulcanized polypropylene/acrylonitrile butadiene rubber/zinc dimethacrylate ternary blend composites containing maleic anhydride grafted polypropylene

Improved melting strength of polypropylene by reactive compounding with ultrafine full-vulcanized polybutadiene rubber (UFBR) particles

Improved Mechanical and Thermal Properties of Polypropylene Blends Based on Diethanolamine-Plasticized Corn Starch Via in Situ Reactive Compatibilization

Mechanism of highly improved electrical properties in polypropylene by chemical modification of grafting maleic anhydride

ADVANCE IN EFFECT OF AGGREGATION STRUCTURE OF PP ON MECHANICAL PROPERTIES

Novel Method for Preparation of Polypropylene Blends with High Melt Strength by Reactive Compounding