Abstract:The ductility of sheet metal is typically limited by either localized necking or by damage and fracture. A recent ductility classification refers to these failure modes respectively as "global" and "local" formability. The forming limit curve (FLC) and the uniaxial tensile test assess global formability, whereas the fracture forming limit (FFL), the true thickness fracture strain, hole expansion ratios (HER), etc. are indicators of local formability. Experimental hole expansion data in the literature for different dual-phase (DP) steel grades of similar strength and composition presents a paradox: grades which are found to be ductile in a tensile test and/or FLC show a low ductility in hole expansion, whereas other grades with a low ductility in conventional tests perform surprisingly well at cut edges. In this work, an in-depth systematic statistical analysis of idealized artificial two-phase microstructures is carried out to unravel the underlying mechanisms of the observed paradoxical trends. This is done by scaling the hardness of martensite and its volume fraction to generate virtual DP steels of the same strength but different strain hardening and mechanical phase contrast (hardness difference). The proposed micromechanical model adequately reproduces the experimentally observed trends. The results show that in DP steels, a higher global (necking-driven) ductility is obtained upon delaying martensite plasticity by increasing the mechanical contrast of the two phases. Consequently, the stress–strain distributions becomes more heterogeneous, resulting in a lower fracture limit of one of the phases or interfaces in shear loading, thereby, reducing the local ductility. Global ductility is improved by higher mechanical phase contrast and lower martensite volume fraction, whereas local ductility is improved by low phase contrast and higher martensite volume fraction. The hardening behavior of martensite is the key to avoiding the above trade-off between local and global ductility. It is shown that if the strain hardening capacity of martensite in the later stages of deformation (in high strains) can be increased, this would result in removing the observed paradoxical trends of local and global ductility in DP steels.

Mutual mechanical effects of ferrite and martensite in a low alloy ferrite-martensite dual phase steel

Investigation of Micromechanical Properties of Martensite and Ferrite Microphases in a 35CHGSA Medium‐Si Low‐Alloy Steel

Effect of prior austenite carbon partitioning on martensite hardening variation in a low alloy ferrite–martensite dual phase steel

Effect of martensite morphology and volume fraction on strain hardening and fracture behavior of martensite–ferrite dual phase steel

Effects of martensite particle size and spatial distribution on work hardening behaviour of fine-grained dual-phase steel

Effect of hardness of martensite and ferrite on void formation in dual phase steel

Simultaneous enhancement of strength and ductility in ferrite-martensite steel via increasing the martensite fraction

Effect of Ferrite/Martensite Phase Size on Tensile Behavior of Dual-Phase Steels with Nano-Precipitation of Vanadium Carbides

Understanding ferrite deformation caused by austenite to martensite transformation in dual phase steels

Effect of α‐Ferrite on Plasticity and Fracture Mechanisms of Dual‐Phase Ultrastrong Heterolamellar Steels

The effect of ferrite–martensite morphology on the scratch and abrasive wear behaviour of a dual phase construction steel

Microstructure, mechanical properties and strengthening mechanism of high strength hot-rolled ferrite-martensite dual phase steel

A novel technique for developing a dual-phase steel with a lower strength difference between ferrite and martensite

Effect of Variation of Martensite with a Constant Carbon Content on Mechanical Behavior and Sliding Wear of Dual Phase Steels

On the critical role of martensite hardening behavior in the paradox of local and global ductility in dual-phase steels

On the mechanical heterogeneity in dual phase steel grades: Activation of slip systems and deformation of martensite in DP800

Micromechanism involved in ultrafine grained ferrite/martensite dual phase steels strengthened by nanoscale Cu-rich precipitates

Dissimilar Resistance Spot Welding of Ferrite-Martensite Dual Phase Steel/Low Carbon Steel: Phase Transformations and Mechanical Properties

The synergistic effects of ultrafine grains and nano-size Cu-rich precipitates on the mechanical properties of DP steels

Medium-carbon dual-phase steels with spheroidized ferrite matrix

Effect of microstructure heterogeneity on the mechanical properties of friction stir welded reduced activation ferritic/martensitic steel