Abstract:<p>A co-precipitation hardened medium-Mn steel with respective NiAl and Cu-rich particles in dual phases (austenite and ferrite) has been designed by using a quenching-partitioning-tempering (QPT) treatment. The influences of co-precipitates on the elasto-plastic transition and strain compatibility has been investigated based on the micro-mechanical behavior of constituent phases, the evolution of lattice strain and stress components. Compared to the Cu-Free steel, in which single NiAl precipitates form in ferrite, co-precipitation in the Cu-Added steel results in an improved strain compatibility between austenite (γ) and ferrite (α). The lattice strains of both γ and α phases show similar evolutions during the entire strain regime, and a homogeneous elasto-plastic deformation occurs together with a continuous yielding and weak transient of strain hardening rate. The improved strain compatibility leads to an alleviation of strain localization in the phase interfaces, so that the overall back stress increases slowly with the tensile strain increasing during the whole plastic deformation process, although the transformation-induced plasticity (TRIP) effect of the Cu-Added steel only occurs at low strains (<5%) due to the low mechanical stability of the retained austenite. In contrast, a non-continuous yielding of the constituent phases occurs in the Cu-Free steel leads to strong strain transfer across the α/γ interfaces due to a low deformation compatibility between austenite and ferrite. High internal stress in the phase interfaces results in easy damage-crack formation, but it can be accommodated by the TRIP effect which dominates in large strains, resulting in back stress decreasing and effective stress hardening during the subsequent deformation stage. However, the introduction of hydrogen can aggravate the dislocation accumulation and strain transfer between austenite and ferrite; thus, hydrogen-induced cracks (HICs) are prone to nucleate at the α/γ interfaces while the TRIP effect is not significant, leading to premature failure and significant elongation loss (85.4%) of the Cu-Free steel. Therefore, the improved strain compatibility of the Cu-Added steel contributes to a better resistance to hydrogen embrittlement, although both medium Mn steels possess similar tensile strength (1 GPa) and elongation (25%) values.</p>

Effect of α‐Ferrite on Plasticity and Fracture Mechanisms of Dual‐Phase Ultrastrong Heterolamellar Steels

Achieving Unexpected Strength and Ductility Synergies in Heterogeneous Metastable Lamellar Steels

Effect of Ferrite/Martensite Phase Size on Tensile Behavior of Dual-Phase Steels with Nano-Precipitation of Vanadium Carbides

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Light-weight Isometric-Phase Steels with Superior Strength-Hardness-ductility Combination

Microscale mechanisms of plasticity and damage in advanced multi-phase steels

Achieving High Strength and High Ductility of Dual-Phase Steel Via Alternating Lamellar Microstructure

Effect of hardness of martensite and ferrite on void formation in dual phase steel

Enhanced Strength-Plasticity Matching of Lamellar 1 GPa-grade Dual-Phase Steels Via Cyclic Intercritical Quenching

Ensuring the strength and ductility synergy in an austenitic stainless steel: single- or multi-phase hetero-structures design

Microstructure, mechanical properties and strengthening mechanism of high strength hot-rolled ferrite-martensite dual phase steel

Design of Tri-Phase Lamellar Architectures for Enhanced Ductility in Ultra-Strong Steel

Improving strength-ductility balance of a brittle Al-doped FeCrNi multi-principal element alloy by introducing a heterostructure with hard phase enveloping soft phase

Superior fracture toughness in a high-strength austenitic steel with heterogeneous lamellar microstructure

Extensive anisotropic lath martensite plasticity in dual-phase steels: A numerical-experimental investigation

A Hierarchical Theoretical Model for Mechanical Properties of Lath Martensitic Steels

Effects of plasticity-induced martensitic transformation and grain refinement on the evolution of microstructure and mechanical properties of a metastable high entropy alloy

Homogeneous elasto-plastic deformation and improved strain compatibility between austenite and ferrite in a co-precipitation hardened medium Mn steel with enhanced hydrogen embrittlement resistance

Enhanced strength and ductility of the low-carbon steel with heterogeneous lamellar dual-phase structure produced by cyclic intercritical rolling

Effect of martensite morphology and volume fraction on strain hardening and fracture behavior of martensite–ferrite dual phase steel

Simultaneous enhancement of strength and ductility in ferrite-martensite steel via increasing the martensite fraction