Abstract:Silicon based power micro-electro-mechanical system (MEMS) applications require highspeed microrotating machinery operating stably over a large range of operating conditions. The technical barriers to achieving stable high-speed operation with micro-gas-bearings are governed by (1) stringent fabrication tolerance requirements and manufacturing repeatability, (2) structural integrity of the silicon rotors, (3) rotordynamic coupling effects due to leakage flows, (4) bearing losses and power requirements, and (5) transcritical operation and whirl instability issues. To enable high-power density the micro-turbomachinery must be run at tip speeds comparable to conventional scale turbomachinery. The rotors of the micro-gas turbines are supported by hydrostatic gas journal and hydrostatic gas thrust bearings. Dictated by fabrication constraints the location of the gas journal bearings is at the outer periphery of the rotor. The high bearing surface speeds (target nearly 10 x 10(6) mm rpm), the very low bearing aspect ratios (L/D < 0.1), and the laminar flow regime in the bearing gap (Re < 500) place these micro-bearing designs into unexplored regimes in the parameter space. A gas-bearing supported micro-air turbine was developed with the objectives of demonstrating repeatable, stable high-speed gas-bearing operation and verifying the previously developed micro-gas-bearing analytical models. The paper synthesizes and integrates the established micro-gas-bearing theories and insight gained from extensive experimental work. The characteristics of the new micro-air turbine include a four-chamber journal bearing feed system to introduce stiffness anisotropy, labyrinth seals to avoid rotordynamic coupling effects of leakage flows, a reinforced thrust bearing structural design, a redesigned turbine rotor to increase power, a symmetric feed system to avoid flow and force nonuniformity, and a new rotor micro-fabrication methodology for reduced rotor imbalance. A large number of test devices were successfully manufactured demonstrating repeatable bearing geometry. More specifically, three sets of devices with different journal bearing clearances were produced to investigate the dynamic behavior as a function of bearing geometry. Experiments were conducted to characterize the "as-fabricated" bearing geometry, the damping ratio, and the natural frequencies. Repeatable high-speed bearing operation was demonstrated using isotropic and anisotropic bearing settings reaching whirl-ratios between 20 and 40. A rotor speed of 1.7 x 10(6) rpm (equivalent to 370 m/s blade tip speed or a bearing DN number of 7 x 10(6) mm rpm) was achieved demonstrating the feasibility of MEMS-based micro-scale rotating machinery and validating key aspects of the micro-gas-bearing theory. [DOI: 10.1115/1.3123343]

A Silicon-Based Micro Gas Turbine Engine for Power Generation

Design and Fabrication of a Silicon-Based Micro Combustor for Micro Gas Turbine Engine

Power Mems and Microengines

Research Project on Micromachined Gas Turbine Generators

Experimental Study of Combustion on a Micro Gas Turbine Combustor

Experimental Investigation of a Novel Micro Gas Turbine with Flexible Switching Function for Distributed Power System

High-Speed Operation of a Gas-Bearing Supported MEMS-Air Turbine

Design and Fabrication of the Micro Turbine for Micro Gas Turbine Engine

Analysis on the development of micro gas turbine generation technology

Fabrication and Testing of a High-Speed Microscale Turbocharger

The Experimental Study on Ignition Mechanism and Combustion Characteristics of Micro Gas Engine

Fully Coupled Whole-Annulus Investigation of Combustor–Turbine Interaction with Reacting Flow

Design and Numerical Simulation of a Micro-Gas Turbine Combustor

Specific Features of Advanced Micro Gas Turbines and Their Application Prospects

Combustion Characteristics of A Micro Gas Turbine Combustor with Gamma-Shaped Porous Media Dome

Design and Test of Small-Scale Rotary Engine Power System

A Development of Meso-Scale Vortex Combustion for a Micro Power Generator Based on a Thermoelectric Generator

Start-up and Self-sustain Test of 500 W Ultra-Micro Gas Turbine Generator

Development of a micro-combined heat and power powered by an opposed-piston engine in building applications

Research on combustion performance of a micro-mixing combustor for methane-fueled gas turbine

Parametric Simulations On Leakage And Performance Of A Miniature Free-Piston Generator (Mfpg)