Abstract:Alumina (Al2O3) ceramics are widely used in electronics, machinery, healthcare, and other fields due to their excellent hardness and high temperature stability. However, their high brittleness limits further applications, such as artificial ceramic implants and highly flexible protective gear. To address the limitations of single-phase toughening in Al2O3 ceramics, some researchers have introduced a second phase to enhance these ceramics. However, introducing a single phase still limits the range of performance improvement. Therefore, this study explores the printing of Al2O3 ceramics by adding two different phases. Additionally, a new gradient printing technique is proposed to overcome the limitations of single material homogeneity, such as uniform performance and the presence of large residual stresses. Unlike traditional vat photopolymerization printing technology, this study stands out by generating green bodies with varying second-phase particle ratios across different layers. This study investigated the effects of different contents of sepiolite fiber (SF) and 316L stainless steel (SS) on various aspects of microstructure, phase composition, physical properties, and mechanical properties of gradient-printed Al2O3. The experimental results demonstrate that compared to Al2O3 parts without added SF and 316L SS, the inclusion of these materials can significantly reduce porosity and water absorption, resulting in a denser structure. In addition, the substantial improvements, with an increase of 394.4% in flexural strength and an increase of 316.7% in toughness, of the Al2O3 components enhanced by incorporating SF and 316L SS have been obtained.

What problem does this paper attempt to address?

The paper primarily focuses on the performance improvement of alumina (Al₂O₃) ceramic materials. Due to its excellent hardness and high-temperature stability, alumina is widely used in electronics, mechanical, medical, and other fields. However, its inherent brittleness limits its further application in areas such as artificial ceramic implants and high-flexibility protective equipment. To overcome these limitations, researchers have introduced a second phase to enhance the performance of alumina ceramics. However, the introduction of a single second phase still cannot fully optimize the various properties of the material. Therefore, this paper proposes a new method to improve material performance by adding two different second phases—sepiolite fiber (SF) and 316L stainless steel (SS)—and forming a functionally graded structure in the alumina ceramics. The study employed Vat Photopolymerization (VPP), an additive manufacturing technology that can achieve high precision and temperature stability, reducing the need for complex support structures. Unlike traditional VPP technology, this study developed a novel gradient printing process that can adjust the proportion of second phase particles between different layers to obtain green bodies with varying second phase particle ratios. In this way, researchers were able to prepare alumina ceramic components with more uniform performance and less residual stress. Specifically, the experiment examined the effects of different contents (2wt.%, 4wt.%, 6wt.%, 8wt.%) of sepiolite fiber and 316L stainless steel on the microstructure, phase composition, physical properties, and mechanical properties of alumina ceramics. The experimental results showed that, compared to alumina without these additives, the addition of these materials significantly reduced porosity and water absorption, and increased the material's density. Furthermore, the flexural strength of these enhanced alumina ceramics increased by 394.4%, and toughness improved by 316.7%. In summary, this paper aims to improve the overall performance of alumina ceramics, especially their mechanical strength and toughness, by introducing two different second phase materials and adopting a functionally graded structure design. This innovative approach provides a theoretical basis and technical support for the application of alumina ceramics in the industry.

Vat Photopolymerization of Sepiolite Fiber and 316L Stainless Steel-Reinforced Alumina with Functionally Graded Structures

Vat photopolymerization of sepiolite fiber-toughened alumina: Effects of sepiolite fiber content on microstructures and physical, rheological, and mechanical properties

Effect of Foreign Ion Substitution and Micropore Tuning in Robocasting Single-Phase Bioceramic Scaffolds on the Physicochemical Property and Vascularization

Effect of different sintering additives type on Vat photopolymerization 3D printing of Al2O3 ceramics

Fabrication of alumina ceramics with high flexural strength using stereolithography

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Preparation of high‐strength Si3N4 ceramics via vat photopolymerization: A bi‐phase particle size gradation strategy

Microstructure refinement-homogenization and flexural strength improvement of Al2O3 ceramics fabricated by DLP-stereolithography integrated with chemical precipitation coating process

Mechanical and dielectric properties of Si3N4/β-SiAlON composite ceramics fabricated by vat photopolymerization 3D printing technology

Vat Photopolymerization of Ceramic Parts: Effects of Carbon Fiber Additives on Microstructure and Mechanical Performance

Fabrication of Al2O3 ceramic cores with high porosity and high strength by vat photopolymerization 3D printing and sacrificial templating

Rheological behavior and curing deformation of paste containing 85 wt% Al2O3 ceramic during SLA-3D printing

Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

3D printing of hollow lattice structures of ZrO2(3Y)/Al2O3 ceramics by vat photopolymerization: Process optimization, microstructure evolution and mechanical properties

SiC Nanoparticles Strengthened Alumina Ceramics Prepared by Extrusion Printing

Preparation of high performance dense Al 2 O 3 ceramics by digital light processing 3D printing technology

Effect of particle size distribution and printing parameters on alumina ceramics prepared by Additive Manufacturing

Additive Manufacturing and Characterization of Complex Al2o3 Parts Based on A Novel Stereolithography Method

Additive manufacturing of flexible polymer-derived ceramic matrix composites

Reinforcement effect in printing precision and sintering performance for liquid crystal display stereolithography additive manufacturing of alumina ceramics

Optimization of 3D Printing Parameters for Alumina Ceramic Based on the Orthogonal Test