Abstract:As regards significance of phase transformations and nature of phases developed as well as their affective role in the physical and mechanical properties and also corrosion resistance of ferritic stainless steel (FSS) welds, this paper wishes to investigate phases identification by means of electron backscattered diffraction (EBSD) analysis and mechanical performance via tensile test. For this goal, the sheets of FSS were prepared for the lap joints and successively, were welded by laser beam welding process under different pulse durations. No welding defects such as porosity, crack, etc., were seen, exhibiting prosperous joining process. Optical microscopy and EBSD corroborated the attendance of low-temperature (LT) and high-temperature (HT) heat-affected zone (HAZ). Fine-grained ferrite, intergranular martensite, as well as carbide precipitates were characterized in the LTHAZ, because of rapid cooling from the zone. Whereas, the HTHAZ was composed of coarse-grained ferrite and intergranular martensite by way of quenching from the zone. Phases characterization could show that the fusion zone (FZ) also had extremely coarsened ferrite and martensite at the grain boundaries. Grain coarsening might be responsible for weak crystallographic texture in this zone. The minimum and maximum microhardness allocated to the FZ and LTHAZ which were 174 5 HV and 261 11 HV, respectively. Founded on the tensile testing, it was apprehended that an increase in the pulse duration from 12 to 15 ms promoted the failure load and energy absorption by almost 13 and 327%, respectively. This was caused by joints strengthening through enhancing the weld penetration. However, an increase in the pulse duration from 15 to 18 ms resulted in degrading the failure load and energy absorption by around 31 and 95%, respectively. This arose from joints weakening due to intensifying grain coarsening phenomenon in the weld zone.

Effect of Welding Parameters on Mechanical Performance and Microstructural Characterization of Fiber Laser Oscillation Welded Dissimilar TWIP/304L Steel Joints

Effects of Interlaminar Microstructural Inhomogeneity on Mechanical Properties and Corrosion Resistance of Multi-Layer Fiber Laser Welded High Strength Low Alloy Steel

Effect of beam oscillation on the mechanical properties of fiber-laser-welded thin-plate X2CrTiNb18 ferritic stainless-steel joints

Microstructure evolution and high cycle fatigue failure behavior of friction stir-welded Ti–6Al–4V at varying welding speeds

Effect of Heat Input on Microstructure and Properties of Dissimilar Laser Welded Joints Between TWIP and TRIP Steels

Microstructure- and Strain Rate-Dependent Tensile Behavior of Fiber Laser-Welded DP980 Steel Joint

Dissimilar Laser Welding of Austenitic Stainless Steel and Abrasion-Resistant Steel: Microstructural Evolution and Mechanical Properties Enhanced by Post-Weld Heat Treatment

Interfacial microstructure and mechanical properties of laser-welded 6061Al/AISI304 dissimilar lap joints via beam oscillation

Microstructure and Tensile Behavior of Fiber Laser-Welded Blanks of Dp600 and Dp980 Steels

Melt Flow and Microstructural Characteristics in Beam Oscillation Superimposed Laser Welding of 304 Stainless Steel

Microstructure and Mechanical Properties of Pulsed Laser Welded Al/steel Dissimilar Joint

Effect of laser welding parameters on the temperature distribution, microstructure and mechanical properties of dissimilar weld joint of Inconel 625 and stainless steel 304

Formation, microstructure, and mechanical properties of oscillating laser-welded joints of 8-mm 304 stainless steel

A Study of the Performance of Dissimilar Pulsed-Laser-Welded JSC590R/JAC980YL Steel Joints of Differential Thickness

Study on Microstructure and Properties of Laser Dissimilar Welded Joints of Ultra-High Strength PHS1500/PHS2000 Steel

Effect of parameters on microstructure and mechanical property of dissimilar joints between 316L stainless steel and GH909 alloy by laser welding

Effects of resistance spot welding parameters on microstructure and mechanical properties of the dissimilar welded joint of quenching and partitioning steels

Fiber Laser Welding of 1700-MPa, Ultrahigh-Strength Steel

Microstructure and Mechanical Properties of Laser Welded Dissimilar Joints Between QP and Boron Alloyed Martensitic Steels

Effect of laser oscillating welding on microstructure and mechanical properties of 40Cr steel/45 steel fillet welded joints

On the Microstructural Transformations and Mechanical Performance of Laser Beam Welded UNS S43000 Ferritic Stainless Steel