Abstract:Some components made of titanium alloys will serve in corrosive environments in the industry, and suffer from corrosion and wear at the same time. However, the components exhibit the high wear and corrosion rates due to their low hardness and the extremely thin oxidation film formed on their surfaces, which can accelerate their failure and reduce their service life. In response to this situation, CoCrFeNiNb high-entropy alloys (HEAs) coatings with Y2O3 (0 wt.%, 1 wt.%, 2 wt.%, and 3 wt.%) were successfully prepared on Ti6Al4V by laser cladding. The effects of Y2O3 addition content on the microstructure, corrosion and mechanical properties were investigated comprehensively by X-ray diffractometry (XRD), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), microhardness tests, electrochemical tests and tribocorrosion tests in this work. Other than them, tribocorrosion behaviors of the coatings were especially highlighted in two different environments (neutral (pH 7) and acid (pH 3) solutions). The results showed the significant enhancement in microhardness with the introduction of Y2O3 due to the microstructural refinement and the formation of Laves phase Cr2Nb in the coatings. The coating with 2 wt.% Y2O3 performed the most excellent corrosion resistance (neutral solution: Ecorr=-0.12 V; acid solution: Ecorr=0.043 V) increased by 55.5% and 115.0% of the coating without Y2O3. As well as, the coating also demonstrated the lowest wear rates (neutral solution: 3.32×10−4 mm3·N−1·m−1; acid solution: 2.24×10−4 mm3·N−1·m−1) reduced by 17.8% and 33.3% of the coating without Y2O3. The superior tribocorrosion resistance and corrosion resistance make CoCrFeNiNb+2 wt.% Y2O3 HEA coating show a tremendous potential in aerospace and marine applications application.

Tribo-corrosion performance of Fe-Cr-B alloy coating manufactured by high deposition rate and conventional laser directed energy deposition

Effect of Process Parameters on Microstructure and Properties of AlCoCrFeNi-WC-WS2 Composite Coating Prepared by Laser Cladding

Corrosion resistance and wear behavior of CoCrFeNiMn@Gr high entropy alloy-based composite coatings prepared by laser cladding

Investigation into tribocorrosion behaviors of CoCrFeNiNb laser-clad coatings with Y2O3

Microstructure, mechanical properties and lead-bismuth eutectic corrosion behavior of FeCrAlTiNb high-entropy alloy coatings

A study on the wear and corrosion resistance of high-entropy alloy treated with laser shock peening and PVD coating

Microstructure Evolution and Enhanced Wear Resistance of Al2CrFeNiMo High Entropy Alloy Coating Fabricated by Laser Cladding

Tribological and Corrosion Behavior of HVAF-sprayed (Fe-Tib2)/cnt Composite Coating

Experimental and DFT Studies on Corrosion Behaviors of Laser-Cladded (Feconi)75-Xcrxb15si10 High-Entropy Alloy Coatings

Corrosion Resistance Enhancement of CoCrFeMnNi High-Entropy Alloy with WC Particle Reinforcements via Laser Melting Deposition

Microstructures, High-Temperature Tribological and Electrochemical Mechanisms of FeCoNiCrAl High-Entropy Alloy Coating Prepared by Laser Cladding on a Copper Alloy: Combined TEM and DFT Calculation

Study on the Performance of Fe-Based Alloy Coating on 40Cr Substrate Surface

A Novel FeCrAlWx High Entropy Alloy Coating for Enhancing Lead-Bismuth Eutectic Corrosion Resistance

Microstructure and tribological properties of in-situ M x B reinforced CoCrFeNi HEA composites prepared by laser cladding

A novel AlCrFeMoTi high-entropy alloy coating with a high corrosion-resistance in lead-bismuth eutectic alloy

Effect of Cu-doping on tribological properties of laser-cladded FeCoCrNiCu x high-entropy alloy coatings

Effects of WC on the Microstructure, Wear and Corrosion Resistance of Laser-Deposited CoCrFeNi High Entropy Alloy Coatings

Characterization of the microstructure and self-lubrication properties of a AlCoCrFeNi2.1 eutectic high-entropy alloy with powder-pack boronizing

Achieving excellent wear and corrosion properties in laser additive manufactured CrMnFeCoNi high-entropy alloy by laser shock peening

Assessment of the tribocorrosion performance of a (TiZrNbTaMo)C refractory high entropy alloy carbide coating in a marine environment

Microstructure, abrasive wear and corrosion characterisation of laser metal deposited Fe-30Cr-6Mo-10Ni-2.2C alloy