Abstract:Abstract This paper describes the work conducted by the Canadian Nuclear Safety Commission (CNSC) related to the numerical simulations of reinforced concrete (RC) structures under deformable missile impact. The current paper is a continuation of the work conducted in the frame of the OECD/NEA* IRIS (Improving Robustness Assessment Methodologies for Structures Impacted by Missiles) Phase 3 benchmark project. The concrete mock-up with two simple structures attached, one welded and another bolted, was built and tested at the VTT Technical Research Centre in Espoo, Finland. This mock-up was impacted by three subsequent missiles with varying velocities in order to obtain the damage accumulation. To examine vibration transmission through the mock-up, the simple structures modelling equipment were attached to the rear wall of the structure, while the missile impact was at the centre of the front wall. The parameters of the missiles and the RC structure were selected to ensure a flexible behaviour of the RC target in the impact area with only moderate damages, specifically cracking and permanent deformation without perforation. The non-linear dynamic behaviour of the reinforced concrete slabs under missile impact was analyzed using the commercial FE code LS-DYNA. A hybrid FE model using both 3-D solid and 2-D shell FE models was developed for the target discretization. Since the ultimate objective of this work is to model the entire structure over long time periods, a simplified combined shell-solid model with distributed (smeared) reinforcement was selected and validated. This model employs solid FE around an impact area and shell FE for the rest of the mock-up. Detailed modelling of a large RC structure with all equipment attached leads to a very large finite element (FE) model. Therefore, two-level FE modelling using sub-modelling approach was employed: first, analyze the vibrations of a reinforced concrete structure with simplified equipment modelling, and second, analyze in detail the equipment connected to it. This approach assumes uncoupled dynamic behaviour of the structure and the equipment. While the sub-modelling technique is commonly used in static analysis, a special sensitivity analysis was conducted to prove the applicability of sub-modelling for impact analysis. Finally, the effect of structural damping was examined and the best possible damping was selected. The selected damping values and sub-models resulted in relatively good agreement with the test results for both global (RC mock-up) and local (equipment) behaviour.

Investigation on the aircraft impact resistance of Steel-concrete construction

Sensitivity Analysis of Steel-Plate Concrete Containment against a Large Commercial Aircraft

Impact Behaviors of CFT and CFRP Confined CFT Stub Columns

Improved Seismic Design Using Bolted End Plate Connections For Steel Reinforced Concrete Composite Structures

Influence of Different Sites on Impact Response of Steel-Plate Concrete Containment against a Large Commercial Aircraft

Finite element analysis of single steel-plate concrete composite containment of nuclear power plant under commercial aircraft impact

Investigation of the shear resistances of steel-concrete-steel composite structures with bidirectional webs

Aircraft impact analysis of nuclear safety-related concrete structures: A review

Comparative assessment of impact analysis methods applied to large commercial aircraft crash on reinforced concrete containment

Analysis of impact force of large commercial aircraft on rigid wall and nuclear power plant containment

Comparative analyses of a shield building subjected to a large commercial aircraft impact between decoupling method and coupling method

Design of steel-concrete composite panels under low-velocity impact: Local punching failure

Experimental Study on Scabbing Limit of Local Damage to Reinforced Concrete Panels Subjected to Oblique Impact by Projectile with Semispherical Nose

Numerical Analyses of a Shield Building Subjected to a Large Commercial Aircraft Impact

Analytical Study on Dynamic Response of Reinforced Concrete Structure with Internal Equipment Subjected to Projectile Impact

Investigating the Effect of Supports on Reinforced Concrete Slab Subjected to Oblique Missile Impact

Applicability of Sub-Modelling Technique for Dynamic Analysis of Concrete Structures With Attached Equipment Under Missile Impact

An Experimental Study on the Verification of Structural and Seismic Performance of Steel Composite Walls

Impact response of SCS sandwich slabs with ultra-high performance concrete: failure mechanism and influence of shear connector configuration

Synergistic use of ultra‐high‐performance fiber‐reinforced concrete (UHPFRC) and carbon fiber‐reinforced polymer (CFRP) for improving the impact resistance of concrete‐filled steel tubes

Concrete-encased CFST Members with Circular Sections under Laterally Low Velocity Impact: Analytical Behaviour