Abstract:RationaleThe precision of the standard measurements of reference materials (RMs) is critical to normalize the raw δ15N values of samples to the international scale. Because the measurement configuration is required to moderate the properties of both RMs and samples for obtaining an ideal measurement precision, it is important to determine the appropriate measurement configurations of RMs to achieve accurate nitrogen isotope compositions of samples. Therefore, it is critical to systematically examine RMs for optimizing the configurations and further improve the measurement precision.MethodsGas source isotope ratio mass spectrometry (IRMS) coupled with an online elemental analyzer (EA) equipped with a single‐quartz reactor was performed to analyze the nitrogen isotope compositions. Some adjustments were made as follows: (a) as the in‐house working standard, urea was used to investigate the influences of combustion through moderating the different oxygen injections (0–20 mL) and sample delay times (10–12 s) and optimize the combustion conditions to enhance oxidation ability; (b) CO2 from the sample gas stream was removed to prevent interferences between CO2 and N2; (c) international RMs, including USGS40 (l‐glutamic), IAEA600 (caffeine), and soil standard (B2153) with a low organic content, were systematically analyzed under the optimized configurations, and the precisions of the δ15N values were further examined.ResultsOur results showed that sufficient oxygen should be injected to improve the sample combustion when analyzing δ15N in natural samples such as soil or marine sediment with low organic content. In addition, the measurement precision of δ15N was affected by the tailing of the CO2 peak from the gas chromatography column into the subsequent sample measurement if the EA is equipped with a single‐quartz reactor column. Our adjustments can produce an optimized repeatability and accuracy of the δ15N value, especially for RMs with low organic content, and the uncertainty of the measurements is improved to be better than 0.1‰ under optimized configurations.ConclusionsThe analytical conditions such as the oxygen flow rate and injection time or sample introduction time into the EA need to be adjusted depending on the combustion conditions of the RMs and samples to obtain a reliable accuracy of measurement. We recommend that when analyzing δ15N of natural samples such as soil or marine sediment samples with low organic content, more oxygen should be injected to improve the combustion of the samples. In addition, CO2 should be removed from the sample gas stream before being introduced into the isotope ratio mass spectrometer when the EA is equipped with a single‐quartz reactor.

Optimizations of the EA-IRMS system for δ 15 N analysis of trace nitrogen

Influences of oxidation ability on precision in nitrogen isotope measurements of organic reference materials by EA-IRMS.

On-line measurements of delta(15)N in biological fluids by a modified continuous-flow elemental analyzer with an isotope-ratio mass spectrometer

Influences of Oxidation Ability on Precision in Nitrogen Isotope Measurements of Organic Reference Materials Using Elemental Analysis-Isotope Ratio Mass Spectrometry

Gas Modifier Assisted Re-Circulation Mode High-Field Asymmetric Waveform Ion Mobility Spectrometry (FAIMS)

A proof-of-principle study for δ15N measurements of aqueous dissolved nitrate and nitrite with a modified LC-IRMS interface

A Proof‐of‐Principle Study for δ15N Measurements of Aqueous Dissolved Nitrate With a Modified LC‐IRMS Interface

Improving the measurement of nitrogen stable isotopes in organic materials containing high C:N ratios using a 5A molecular sieve column

Determination of nitrogen isotopes on samples with tens of nmol of N using the combination of an elemental analyzer, a GasBench interface and an isotope ratio mass spectrometer: An evaluation of blank N contributions and blank-correction

Analytical techniques for quantifying (15)N/(14)N of nitrate, nitrite, total dissolved nitrogen and ammonium in environmental samples using a gas chromatograph equipped with a quadrupole mass spectrometer

A Novel Membrane Inlet Mass Spectrometer Method to Measure ¹⁵NH4₄⁺ for Isotope-Enrichment Experiments in Aquatic Ecosystems.

Determination of 15N in Marine Suspended Particulate Matter Using EA-IRMS Technique

Data Normalization and Quality Control of Light Element Stable Isotope Analyses by Means of Continuous Flow Isotope Ratio Mass Spectrometry

Stable Nitrogen Isotope Analysis of Amino Acids by Gas Chromatography-Combustion-Isotope Ratio Mass Spectrometry for High-Resolution Trophic Level Estimation

Experimental assessment of elemental analyzer isotope ratio mass spectrometry normalization methodologies for environmental stable isotopes

A Reliable Compound-Specific Nitrogen Isotope Analysis of Amino Acids by GC-C-IRMS Following Derivatisation into N -Pivaloyl- Iso -Propyl (npip)esters for High-Resolution Food Webs Estimation

Novel GC/Py/GC/IRMS-Based Method for Isotope Measurements of Nitrate and Nitrite. I: Converting Nitrate to Benzyl Nitrate for Δ18o Analysis.

FIRST δ 13 C RESULTS WITH A NEW CONNECTION BETWEEN THE EA-IRMS SYSTEM AND THE GAS INJECTION SYSTEM AT COLOGNEAMS

Membrane inlet mass spectrometry method (REOX/MIMS) to measure 15N-nitrate in isotope-enrichment experiments

Novel GC/Py/GC/IRMS-Based Method for Isotope Measurements of Nitrate and Nitrite. I: Converting Nitrate to Benzyl Nitrate for δ 18 O Analysis

Nitrogen isotopic analysis of nitrate in aquatic environment by cadmium- hydroxylamine hydrochloride reduction.