Abstract:The content of Zn and Mg directly influences the microstructure characteristics of Al–Zn–Mg–Cu alloys. In the present study, the solidification phases of three as-cast Al–Zn–Mg–Cu alloys with different Zn/Mg ratio (1.5, 1.8 and 2.1 at.%, successively) were thoroughly investigated, and their evolutions during homogenizations were analyzed with the aid of optical microscopy (OM), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and X-ray diffraction (XRD). The results showed that serious dendritic segregation existed in the as-cast microstructures. In the as-cast alloys with three different Zn/Mg ratio, the secondary phases are represented by non-equilibrium intermetallic phases (Mg(Zn,Cu,Al) 2 and Al 2 Cu) and precipitate MgZn 2 phase. Thereinto, the Mg(Zn,Cu,Al) 2 phase possessed a majority, which was determined through computational analysis of solidification processes. With the increase of Zn/Mg ratio, the amount of Mg(Zn,Cu,Al) 2 phase continuously decreased, while the content of Al 2 Cu phase showed only minor variation. As the Zn/Mg ratio increased, the strength and hardness of the as-cast alloy gradually improved. The Zn/Mg ratio has a significant impact on the dissolution and transformation of the secondary phases during homogenization process. As the Zn/Mg ratio increased, the melting point of the as-cast eutectic gradually decreased. Additionally, due to the higher diffusion rate of Zn compared to Mg and Cu elements, the dissolution rate of the secondary phase increased accordingly. At relatively low temperatures (380, 410, and 440 °C), phase transformation from the Mg(Zn,Cu,Al) 2 phase to the Al 2 CuMg phase occurred in all three alloys. However, phase transformation was only present in Low/Mid-Zn/Mg ratio alloys at 470 °C. These differences are attributed to the varying diffusion rates of Zn, Mg, and Cu elements during the homogenization process. The implementation of a two-stage homogenization process effectively addresses the issue of residual Al 2 CuMg phase in Low/Mid-Zn/Mg ratio alloys.

Effect of Zn Content and Homogenization Treatment on Mechanical Properties and Corrosion Behavior of Mg-9Y-xZn Alloys

Effect of Volume Fraction of LPSO Phases on Corrosion and Mechanical Properties of Mg-Zn-Y Alloys

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effect of the Morphology of Long-Period Stacking Ordered Phase on Mechanical Properties and Corrosion Behavior of Cast Mg-Zn-Y-Ti Alloy

Effect of Heat Treatment on Corrosion and Mechanical Properties of Mg-10Y-1.5Zn-0.5Zr Alloy

Effect of volume fraction of 18R-LPSO phase on corrosion resistance of Mg−Zn−Y alloys

Effect of the Zn/Mg Ratio on Microstructures, Mechanical Properties and Corrosion Performances of Al-Zn-Mg Alloys

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)

Effect of Zn/Mg ratio on the microstructure and mechanical properties of as-cast Al–Zn–Mg–Cu alloys and the phase transformation during homogenization

Effect of Y Contents on the Microstructure, Mechanical Properties, and Corrosion Behavior of Biomedical Mg‐0.5Zn Alloy

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Effect of Trace Zn on the Mechanical Properties and Corrosion Behavior of Al-Mg-Si Alloys with High Cu

Effect of Zn/(Gd+Y) ratio on the microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy

Microstructure characterization and corrosion behavior of Mg–Y–Zn alloys with different long period stacking ordered structures

Microstructure and mechanical properties with various pre-treatment and Zn content in Mg-Gd-Y-Zn alloys

Corrosion Behavior of Mg-Zn-Y-Zr Alloys in Nacl Solution

Effect of Zn Concentration on the Microstructures and Mechanical Properties of Extruded Mg–7Y–4Gd–0.4Zr Alloys

Microstructure, generation of intermetallic compounds and mechanical strengthening mechanism of as-cast Mg–4Y–xZn alloys

Effect of heat treatment on corrosion behaviors of Mg-6Gd-3Y-0.5Zr alloy

Comparative Study on Corrosion Behavior and Mechanism of As-Cast Mg–Zn–Y and Mg–Zn–Gd Alloys