Abstract:This paper proposes a method of micro-fabrication for the formation of complex non-planar shapes by depositing a colloid evaporative droplet onto topographically structured surfaces. The micro-droplet composed of polyurethane (PU) was self-driven by surface tension to adjust their three-dimensional (3D) shapes bound with the surface of the micro-well array. The micro-wells formed from poly-dimethysiloxane (PDMS) consisted of vertical sidewalls to constrain the fluids as boundary conditions in the Young–Laplace equation until drying. Two types of wetting regimes (fully and partially), corresponding to different droplet volume and allocation, were categorized to perform the shaping process in which evolving fluid contours were self-formed utilizing the general principle of minimal surface energy with certain features of the shape set by the wetting of the PDMS. Using the heterogeneous surfaces, slight-concave circular terraces and half-moon shapes with high curvature were fabricated with micrometer dimensions (well diameter of 900 µm). The formed structures were observed to release themselves from the hydrophobic wells by the de-wetting (de-pinned) process in the completion of evaporation. Moreover, the effects of the boundaries were further explored for half-moon shapes by giving three distinct footprints of the partially wetting droplets. In these cases, both experimental results and numerical calculations were performed and compared to illustrate the significant influence of the fluid contact angle (∼90°) and position with a curved boundary line on final formed shape, in particular for the change of curvature ( = 0.62–1.36). Compared to those traditional assays operated on two-dimensional (2D) flat surfaces, this structured-well one could greatly enhance the control of 3D topographic formation in terms of aspect ratio, thickness and curved degree. This novel operation of micro-fabrication is also appropriate for smaller and complex structures by using drop-on-demand inkjet for commercialized mass-production processes.

Syneresis‐Driven Self‐Refilling Printing of Geometry/Component‐Controlled Nano/Microstructures

Dynamics of Liquid Transfer from Nanoporous Stamps in High-Resolution Flexographic Printing

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

Fast Digital Patterning of Surface Topography Toward Three-Dimensional Shape-Changing Structures

Self-formation and Release of Arbitrary-Curvatured Structures Utilizing Droplet Deposition and Structured Surface

3D Multiscale Micro-/Nanofolds by Femtosecond Laser Intermittent Ablation and Constrained Heating on a Shape Memory Polymer

Fabricating patterned microstructures by embedded droplet printing on immiscible deformable surfaces

Solid-Phase Microcontact Printing for Precise Patterning of Rough Surfaces: Using Polymer-Tethered Elastomeric Stamps for the Transfer of Reactive Silanes

A novel hybrid patterning technique for polymer PDMS micro and nanoscale nozzle by double casting

High-resolution and programmable line-morphologies of material-extrusion 3D printed self-leveling inks

3D Printing by Multiphase Silicone/Water Capillary Inks

Fabrication of Self‐Wrinkling Polymer Films with Tunable Patterns through an Interfacial‐Fuming‐Induced Surface Instability Process

Spongy all-in-liquid materials by in-situ formation of emulsions at oil-water interfaces

On-demand modulation of 3D-printed elastomers using programmable droplet inclusions

A New Strategy of Lithography Based on Phase Separation of Polymer Blends

A 3D Self-Shaping Strategy for Nanoresolution Multicomponent Architectures

Maskless Fabrication of Small-Scale Structures Through Controlling Phase Interactions

Laser‐Assisted Direct Ink Writing for High‐Fidelity Fabrication of Elastomeric Complex Structures

Controlled Formation of Surface Patterns in Metal Films Deposited on Elasticity-Gradient PDMS Substrates.

Fabrication and Functionalization of 3D Printed Polydimethylsiloxane‐Based Microfluidic Devices Obtained through Digital Light Processing

Nanoimprint Lithography and Surface Modification As Prospective Technologies for Heterogeneous Integration