Abstract:Extruded bioprinting is widely used for the biomanufacturing of personalized, complex tissue structures, which requires biomaterial inks with a certain viscosity to enable printing. However, there is still a lack of discussion on the controllable preparation and printability of biomaterial inks with different viscosities. In this paper, biomaterial inks composed of gelatin, sodium alginate, and methylcellulose were utablesed to investigate the feasibility of adjustment of rheological properties, thereby analyzing the effects of different rheological properties on the printing process. Based on the response surface methodology, the relationship between the material components and the rheological properties of biomaterial inks was discussed, followed by the prediction of the rheological properties of biomaterial inks. The prediction accuracies of the power-law index and consistency coefficient could reach 96% and 79%, respectively. The material group can be used to prepare biomaterial inks with different viscosity properties in a wide range. Latin hypercube sampling and computational fluid dynamics were used to analyze the effects of different rheological properties and extrusion pressure on the flow rate at the nozzle. The relationship between the rheological properties of the biomaterial ink and the flow rate was established, and the simulation results showed that the changes in the rheological properties of the biomaterial ink in the high-viscosity region resulted in slight fluctuations in the flow rate, implying that the printing process for high-viscosity biomaterial inks may have better versatility. In addition, based on the characteristics of biomaterial inks, the printing process was optimized from the planning of the print pattern to improve the location accuracy of the starting point, and the length accuracy of filaments can reach 99%. The effect of the overlap between the fill pattern and outer frame on the print quality was investigated to improve the surface quality of complex structures. Furthermore, low- and high-viscosity biomaterial inks were tested, and various printing protocols were discussed for improving printing efficiency or maintaining cell activity. This study provides feasible printing concepts for a wider range of biomaterials to meet the biological requirements of cell culture and tissue engineering.

High-resolution and programmable line-morphologies of material-extrusion 3D printed self-leveling inks

Multimaterial Extrusion of Programmable Periodic Filament Structures Via Modularly Designed Extruder Heads

A Systematic Thermal Analysis for Accurately Predicting the Extrusion Printability of Alginate-Gelatin-Based Hydrogel Bioinks

Computational Study of Extrusion Bioprinting with Jammed Gelatin Microgel-Based Composite Ink

Embedded Extrusion Printing in Yield-Stress-fluid Baths

Numerical Model of Jet Formation During Melt Electrowriting for Fabrication of Precise Structures

Machine Learning Enables Process Optimization of Aerosol Jet 3D Printing Based on the Droplet Morphology.

Rotational Co-extrusion 4D Printing of Heterogeneous Filaments to Enable Sophisticated Shape Morphing

Modeling the Printability of Photocuring and Strength Adjustable Hydrogel Bioink During Projection-Based 3D Bioprinting.

Extrusion-based 3D co-printing: printing material design and novel workflow for fabricating patterned heterogeneous tissue structures

A Systematic Printability Study of Direct Ink Writing Towards High-Resolution Rapid Manufacturing

Optimising printing fidelity of the single-nozzle based multimaterial direct ink writing for 3D food printing

Near-infrared Light-Driven Programmable Shape Memory Polymer for Self-Shaping 3D Printing Methods

On-demand modulation of 3D-printed elastomers using programmable droplet inclusions

Subvoxel-Controlled Microfluidic Printing of Dual-Material and Multi-Structural Filaments

Printing Patterned Fine 3d Structures By Manipulating The Three Phase Contact Line

New Strategies for High Efficiency and Precision Bioprinting by DOE Technology and Machine Learning

Investigation of Biomaterial Ink Viscosity Properties and Optimization of the Printing Process Based on Pattern Path Planning

Direct 3D printing functional surfaces stacked with microstructured filaments

Biomimetic Nonuniform, Dual-Stimuli Self-Morphing Enabled by Gradient Four-Dimensional Printing

Rapid Fabrication of Rounded Microchannels Via Extrusion Printing of Molds Using a Thixotropic Ink