Abstract:The results of studying the influence of mechanical alloying (MA) on the surface morphology, microstructure, and atomic–crystalline structure of particles of the Fe–Cr–Co–Ni–Mn multicomponent powder mixture are presented. The initial components are as follows: the R-10 radio-engineering carbonyl iron powder with average particle size d = 3.5 μm, the NPE-1 nickel powder with d = 150 μm, the PK-1u cobalt powder with d < 71 μm, the PKh-1M chromium powder with d < 125 μm, and the MR0 manganese powder with d < 400 μm. The MA of the prepared mixture was performed in an AGO-2 water-cooled mechanical activator using 9-mm steel balls with an acceleration of 90 g in air. The alloying time varies from 5 to 90 min. The ratio of the ball weight to the mixture weight is 20 : 1. X-ray diffraction patterns of the initial and alloyed mixtures, as well as of the sample formed by sintering, are recorded using a DRON 3M diffractometer in Fe K α radiation at 2θ = 30–100°. The microstructure of the mixture particles and the compact sample metallographic specimen after sintering are investigated by scanning electron microscopy. It is established that the peaks of initial components are absent in the X-ray diffraction pattern after mechanical activation for 90 min, and peaks corresponding to the phase representing the γ-Fe-based solid solution having a face-centered crystal lattice are presented. Herewith, the fraction of the amorphous phase increases to 20%. A compact single-phase material is formed from the mixture prepared after 90-min alloying by spark plasma sintering at 800°C for 10 min. Its density is 7.49 kg/cm 3 , resistivity is 0.94–0.96 × 10 –6 Ω m, and microhardness is 306–328 kg/mm 2 . The phase is uniformly distributed over the volume.

Strenghthening features of mechanically alloyed Al-Mn-Cu alloy

The Microstructure and Properties of Al–Mn–Cu–Zr Alloy after High-Energy Ball Milling and Hot-Press Sintering

Effect of Mechanical Alloying on the Dissolution of the Elemental Mn and Al-Mn Compound in Aluminum

Mechanical behaviors of novel multiple principal elements CuAl10Fe5Ni5Mn1.2 wt% with micro-nano structures

Structure and mechanical properties of high strength austenitic Mn–Ni–Cu–V–C dispersionally hardened steel

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Effect of Mn/Ag Ratio on Microstructure and Mechanical Properties of Heat-Resistant Al-Cu Alloys

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Microstructure evolution, mechanical property response and strengthening mechanism induced by compositional effects in Al–6 Mg alloys

Microstructure and properties of Al-4.8Cu-0.45Mn-0.19Cd-0.18Ti-0.17Zr-0.14V aluminum alloy extrusion bar

Influence of the Al Content on the Properties of Mechanically Alloyed CoCrFeNiMnXAl20-X High-Entropy Alloys

Preparation and characterisation of the Al-Cr-Fe-Mn-Mo high-entropy alloy reinforced by in-situ formed carbides

Understanding effect of Mg and Mn equivalents on columnar-to-equiaxed transition of high-strength Al alloy fabricated by laser powder bed fusion

Microstructure and Mechanical Properties of Al-Cu-Mn Alloy Mechanically Alloyed with 5 wt% Zr After Multi-Directional Forging

Precipitates strengthening mechanism of a new squeeze-cast Al-Cu-Li-Mn alloy with high strength and ductility

Microstructural and mechanical behavior of Al-Mg-Mn-Sc-Zr alloy subjected to multi-axial forging at room temperature

Microstructure and property of Al67Mn8Ti24Nb1 intermetallics consolidated with metasable powder

Synergistic strengthening mechanism and microstructural evolution of Al-Zn-Mg-Cu/ Al2O3/Y2O3 hybrid nanocomposite via mechanical alloying and hot pressing

Microstructural evolution and mechanical properties of an ultrahigh-strength Al−Zn−Mg−Cu alloy via powder metallurgy and hot extrusion

Mechanical Alloying with the Partial Amorphization of the Fe–Cr–Co–Ni–Mn Multicomponent Powder Mixture and Its Spark Plasma Sintering to Produce a Compact High-Entropy Material

Mechanical Properties of Cu70Fe30 (at%) Bulk Metastable Alloys Prepared by Mechanical Alloying and Spark Plasma Sintering