Abstract:The effects of the area reductions on the crystal orientation, eccentricity, and mechanical properties of GH4145 alloy tubes prepared by three-roller cold rolling were studied. Electron backscattered diffraction analysis showed that the equiaxed grains of the annealed tube blank gradually changed into elongated crystals along the axial direction (AD) with increased deformation. In addition, the grain orientations rotated from random distribution towards the <101>//radial direction (RD), <111>//AD, and <101> + <111>//tangential direction (TD). Brass, copper, S, and {123}< 111‾ > textures formed and increased in strength with increasing strain. Room-temperature tensile tests loaded along the AD and TD demonstrated yielding anisotropy of the tubes. With increasing strain, the work hardening increased continuously, and the dislocations slipped in three directions and then transformed into slip bands and dislocation cells, whereas a few deformation twins formed as the reduction reached 64%, and then slipped in two directions. When the reduction was 64%, the activated slip system transformed from {111}<110> to {110}<001> in most grains under applied AD loading, which was consistent with the loading in both directions at a reduction of 72%. As the grains in the preferential deformation zone near the inner and outer walls rotated to the <101>//RD orientation, the tubes plastically deformed, and the grains in the central layer then gradually begin to rotate. The ratio of radial length in the deformation hysteresis zone to wall thickness was used to represent the degree of non-uniformity of the deformation. A direct correlation was found between the eccentricity of the wall thickness and the non-uniformity of tube deformation as the area reduction increased from 13% to 50%. In addition, the radial delamination of the tubes disappeared, deformation became uniform, and the eccentricity decreased significantly as the area reduction increase up to 64%. Therefore, the dimensional accuracy and uniformity of the tubes can be further improved by controlling the strain of the tube.

Effect of cold Pilger rolling followed by annealing on fatigue crack initiation in Zircaloy-4 alloy cladding tube

Deformation mechanism and cyclic stress response of Zircaloy-4 alloy cladding tube during low cycle fatigue at room temperature

Microscopic Characterization on Low Cycle Fatigue Behavior at Room Temperature of Zircaloy-4 Alloy with Recrystallized Microstructure

Fretting fatigue tests and crack initiation analysis on zircaloy tube specimens

Texture development and mechanical behavior of Zircaloy-4 alloy plates fabricated by cold rolling and annealing

Recrystallization and texture evolution of warm-pilgered FeCrAl alloy tube during annealing at 850°C

Microstructural and Textural Evolution of a Zr-Sn-Nb-Fe Alloy Tube During Cold Pilger Rolling

Effect of test temperature on low cycle fatigue behavior of zircaloy-4

Microstructure and texture evolutions in FeCrAl cladding tube during pilger processing

Fatigue Crack Growth Behavior of Beta-Annealed Ti–6Al–2Sn–4Zr–xMo (x = 2, 4 and 6) Alloys: Influence of Microstructure and Stress Ratio

Effect of surface nanocrystallization on thermomechanical fatigue behavior of Ti-2Al-2.5Zr alloy tube

Effect of surface nanocrystallization on high-cycle fatigue behavior of Ti–2Al–2.5Zr alloy tube

Biaxial Fatigue Property Enhancement of Gradient Ultra-Fine-grained Zircaloy-4 Prepared by Surface Mechanical Rolling Treatment

Effect of uniaxial loading direction on mechanical responses and texture evolution in cold pilgered Zircaloy-4 tube: Experiments and modeling

The effect of short-term annealing in an Ar environment on microstructure and adhesion property of Cr-coated Zircaloy-4 claddings

Effects of long-time annealing on the microstructures and shear tensile strengths of diffusion-bonded FeCrAl/N18 clad plates

On the mechanism of zircaloy-4 fatigue-deformation under different heat-treatment conditions

Effects of Pre-Crack Depth and Hydrogen Absorption on the Failure Strain of Zircaloy-4 Cladding Tubes Under Biaxial Strain Conditions

Effect of Annealing Treatment on Microstructure and Fatigue Crack Growth Behavior of Al–Zn–Mg–Sc–Zr Alloy

Effect of Cold Rolling Degree on Texture Evolution, Eccentricity, and Yielding Anisotropy of GH4145 Alloy Tubes

Effect of annealing on microstructure and mechanical properties of Mg/Al clad plate