Abstract:The strength of prestressed steel strands has developed towards high strength, increasing from 1860 MPa to over 2200 MPa. The stress in the prestressed anchorage zone is more concentrated and complex, and the anchor plates for dispersed loads need to be optimized in design. This article proposes a design scheme for adding a middle pressure-bearing step based on the existing anchor plate and then establishes a 1/4 model of the concrete anchoring area of the anchor plate for finite element analysis. Based on the theory of the strut-and-tie model, the position of the middle pressure-bearing step is determined according to the maximum angle of the strut-and-tie model. Then, carry out force transfer tests in the anchorage zone for verification. The research results indicate that after adding a middle pressure bearing step to the anchor plate, the angle between the strut-and-tie model in the anchorage zone increases, and the bearing capacity improves. The position of the middle pressure-bearing step in the anchor plate is different, and the angle between the strut-and-tie models is different. According to the middle step position parameter, λ (the ratio of the effective width of the middle step to the distance from the middle step to the end face of the anchor plate) is 0.533 to optimize the anchor plate, and the bearing capacity of its anchorage zone is relatively high. The main tensile and main compressive stresses of the anchor plate after optimization increased by 6.2% and 5.74%, respectively, compared to the anchor plate before optimization. The main tensile stress of the spiral reinforcement under the anchor plate decreased by 0.59%, the main compressive stress decreased by 2.89%, and the von-Mises stress decreased by 2.32%. The side surface tensile stress of concrete under the anchor plate was reduced by 4.3 percent. Finally, three concrete specimens were poured for force transfer testing in the anchorage zone, verifying the safety and reliability of the optimized anchor plate in the 2200 MPa-level prestressed anchorage zone.

Stress state analysis and symmetrical optimization of double-row non-symmetrical arrangement of anchorage slot in concrete lining structure

Comparative study on layout patterns of anchorage slots for pre-stressed lining with unbonded circular anchored tendons

The Finite Element Analysis of the End Anchorage under Larger Prestressing Load in Rehabilitation Engineering

Internal Force Calculation and Stability Analysis of the Slope Reinforced by Pre-Stressed Anchor Cables and Frame Beams

Analytical Method for Structural Analysis of Segmental Lining Interaction with Nonlinear Surrounding Soil and Its Application in Physical Test Interpretation

Comparative Study Of Anchor Double-Row Piles And Frame Double-Row Piles

Optimized Design of Anchor Plates for 2200 MPa-Class Prestressing Anchorage Zones

Numerical Modeling Method and Experimental Verification of Prestressed Lining with Unbonded Annular Anchors

Stability Analysis Of Close-Located Underground Caverns Based On Tunnel Lining And Equivalent Anchor Bolt Simulation

Analysis on Deformation Failure and Structural Mechanical Characteristics of Multistage Loess Slope Supported by Frame Structure with Anchors

Full-scale experiment on the bearing and deformation characteristics for prestressed double-layered shield tunnel linings under high internal pressure

Field Measurement and Numerical Simulation Analysis of High and Steep Slope Reinforced by Prestressed Anchor

Shear behavior of anchor blocks in externally prestressed concrete bridges

Stress Analysis on Steel Anchor Block of External Prestressing Concrete Bridges

Experimental Study on the Axial Compression Performance of an Underwater Concrete Pier Strengthened by Self-Stressed Anti-Washout Concrete and Segments

Reinforcement Analysis of Toe Blocks and Anchor Cables at the Xiluodu Super-High Arch Dam

THEORETICAL ANALYSIS OF INTERACTION BETWEEN SURROUNDING ROCKS AND LINGING STRCTURE OF SHIELD TUNNEL BASED ON DRUCKER-PRAGER YIELD CRITERIA

Experimental Study on Double Row Micropiles and Anchors Composite Retaining Structure in Deep Fill Site

RESEARCH ON COORDINATION MECHANISM OF SLOPE ANCHORING AND REINFORCEMENT

Stress analysis and structure optimization for pre-stressed concrete exterior wall of large-scale LNG storage tank

Study of Shallow Unloading Mechanism and Stability of Foundation Interface of Super High Arch Dam