Abstract:In recent years, the use of CFRP with titanium and/or aluminum to form materials for stacking has gained popularity for aircraft construction. In practice, single-shot drilling is used to create perfectly aligned holes for the composite-metal stack. Usually, standard twist drills, which are commonly available from tool suppliers, are used for practical reasons. However, existing twist drill bits exhibit rapid wear upon the drilling of composite-metal stack layers in single shot, due to the widely contrasting properties of the composite-metal stack, which causes poor surface quality. The stringent quality requirements for aircraft component manufacturing demands frequent drill bit replacement and thus incurs additional costs, a concern still unresolved for aircraft component manufacturers. Owing to highly contrasting properties of a composite-metal stack, it is obvious that standard twist drill cannot fulfil the rigorous drilling requirements, as it is pushed to the limit for the fabrication of high-quality, defect-free holes. In this work, customised twist drills of a tungsten carbide (WC) material with different geometric features were specially fabricated and tested. Twenty drill bits with customised geometries of varying chisel edge angle (30-45°), primary clearance angle (6-8°), and point angle (130-140°) were fabricated. The stacked-up materials used in this study was CFRP and aluminum alloy 7075-T6 (Al7075-T6) with a total thickness of 3.587 mm. This study aims to investigate the effect of twist drill geometry on hole quality using drilling thrust force signature as indicator. All drilling experiments were performed at spindle speed of 2600 rev/min and feed rate of 0.05 mm/rev. Design of experiments utilising response surface methodology (RSM) method was used to construct the experimental array. Analysis of variance (ANOVA) was used to study the effect of parameters and their significance to the thrust force and thus the hole quality. The study shows that the most significant parameter affecting the drilling thrust force and hole surface roughness is primary clearance angle, followed by chisel edge angle. Correlation models of CFRP thrust force (Y1), Al7075-T6 thrust force (Y2), CFRP hole surface roughness (Y3), Al7075-T6 hole surface roughness (Y4) as a function of the tool geometry were established. The results indicated that the proposed correlation models could be used to predict the performance indicators within the limit of factors investigated. The optimum twist drill geometry was established at 45° of chisel edge angle, 7° of primary clearance angle, and 130° of point angle for the drilling of CFRP/Al7075-T6 stack material in a single-shot process. The error between the predicted and actual experiment values was between 6.64% and 8.17% for the optimum drill geometry. The results from this work contribute new knowledge to drilling thrust force signature and hole quality in the single-shot drilling of composite-metal stacks and, specifically, could be used as a practical guideline for the single-shot drilling of CFRP/Al7075-T6 stack for aircraft manufacturing.

One-shot drilling process for thin CFRP/Aluminium alloys stacks

Process parameter auto-adaptation strategy for one-up drilling of CFRP/aluminium hybrid stack

Processing research on orbital drilling of CFRP/Ti-6Al-4V stacks

Hole Diameter Variation and Roundness in Dry Orbital Drilling of Cfrp/Ti Stacks

A Force Sensorless Method for CFRP/Ti Stack Interface Detection During Robotic Orbital Drilling Operations

A Review on Drilling of Multilayer Fiber-Reinforced Polymer Composites and Aluminum Stacks: Optimization of Strategies for Improving the Drilling Performance of Aerospace Assemblies

Multi-Objective Optimization in Single-Shot Drilling of CFRP/Al Stacks Using Customized Twist Drill

Process design and experimental study on drilling operations of a hybrid aluminum/carbon fiber reinforced polymer/titanium composite

Drilling-induced damage suppression on CFRP/Ti-6Al-4V stacks using textured drills

Tool Wear Mechanism in Cutting of Stack CFRP/UNS A97075

Investigation on the cutting responses of CFRP/Ti stacks: With special emphasis on the effects of drilling sequences

Establishing cutting conditions for dry drilling of aluminium alloy stack materials

! Investigation on the Non-Coaxiality in the Drilling of Carbon-Fibre-reinforced Plastic and Aluminium Stacks

Experimental investigation on drilling machinability and hole quality of CFRP/Ti6Al4V stacks under different cooling conditions

Numerical and theoretical approach to evaluate the clamping force and the interlayer gap extent during drilling of stacked materials

Smart Multi-Sensor Monitoring in Drilling of CFRP/CFRP Composite Material Stacks for Aerospace Assembly Applications

Experimental Study on Longitudinal-Torsional Ultrasonic Vibration Drilling of Carbon Fiber–reinforced Plastics/titanium Alloy Stacks

Impact of cooled compressed air and high-speed cutting on the drilling of hybrid composite-metal stacks

Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks

High reliability model of mechanical response in drilling of CFRP/Al stacks

Influence of Metal Chips on Drilling Quality of Carbon Fiber Reinforced Plastic and Titanium Stacks