Abstract:The effect of major constituents (the Li content increases from 0.5 to 3 wt% and the Cu content decreases from 4.5 to 2 wt%) on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations. Increasing the Li content progressively raises the melting temperature from 520 °C in 1# alloy (Al-0.5Li-4.5Cu, wt%) and 2# alloy (Al-1Li-4.5Cu) to 560 °C in 6# alloy (Al-3Li-2Cu). In addition, the variations of the major constituents result in the changes of the type and volume fraction of the inter- and intra-granular intermetallic phases. TEM results indicate that minor modifications to alloy composition greatly alter precipitation behavior during isothermal aging. The Li-poor alloy (2# alloy) presents a much shorter incubation time of T1-Al2CuLi precipitate than the Li-rich alloy (Al-1.5Li-4.5Cu, 3# alloy), while the nucleation of θ'-Al2Cu precipitate is promoted in Li-rich alloy. No typical spherical δ'-Al3Li precipitate is observed in 2# and 3# alloys during isothermal aging, except for the as-quenched 3# alloy. The preferential nucleation of δ' precipitate on the coherent and broad face of θ' precipitate is observed in 2# and 3# alloys, leading to the formation of "sandwich-like" δ'/θ'/δ' phases. Further decreasing Cu content to 2 wt% and increasing Li content to 3 wt% (6# alloy), the predominant phase in the matrix is δ' precipitate, accompanied by a small amount of unevenly distributed θ' and T1 precipitates. The best balance between ductility and strength is obtained by 2# alloy aged for 32 h, but 6# alloy has significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over 2# alloy (density: 2.675 g/cm3; elastic modulus: 75.45 GPa).

Localized corrosion at nm-scale hardening precipitates in Al-Cu-Li alloys

Time-varying electrochemically heterogeneous entities during the micro-galvanic corrosion associated with nanoscale precipitates in an Al-Cu-Li alloy

Initial localized corrosion induced by multiscale precipitates in the new generation high-strength Al-Zn-Mg-Cu alloy

Precipitate microstructures, mechanical properties and corrosion resistance of Al-1.0 wt%Cu-2.5 wt%Li alloys with different micro-alloyed elements addition

Characterization of localized corrosion pathways in 2195-T8 Al–Li alloys exposed to acidic solution

Direct Observation of Atomic-Scale Origins of Local Dissolution in Al-Cu-Mg Alloys

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Towards a better understanding of localised corrosion induced by typical non-metallic inclusions in low-alloy steels

Segregation of S precipitates at T/Al interfaces and relevant effects on localized corrosion mechanisms in Al-Cu-Mg alloy

The effect of major constituents on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy

Corrosion behavior characterization of as extruded Mg-8Li-3Al alloy with minor alloying elements (Gd, Sn and Cu) by scanning Kelvin probe force microscopy

Study on the microstructure and age hardening capability in Al–Cu–Li alloys with different Cu/Li ratio

Localized corrosion of thermally aged Cu-containing Ni-13Cr-10Fe alloys: The role of Cu enrichment induced grain boundary sensitization

Influence of Cu content on the hardenability of Al-xCu-1.1Li alloys

Effect of grain structures and precipitation characteristics on the corrosion behaviour of Sc-containing Al-Cu-Li alloy

Role of intermetallic phases in initiation and propagation of intergranular corrosion of an Al-Li-Cu-Mg alloy

Localized corrosion behaviour of AA6082-T6 Al-Mg-Si alloy: The influence of near-surface deformed layer

Corrosion and Characterisation of Dual Phase Mg–Li–Ca Alloy in Hank’s Solution: the Influence of Microstructural Features

On the Formation Trajectory of Diverse Corrosion Morphologies Associated with T Phases in an Al-Cu-Li Alloy

The influence of Cu/Li ratio on precipitation in Al–Cu–Li–x alloys

In-situ AFM and quasi-in-situ studies for localized corrosion in Mg-9Al-1Fe-(Gd) alloys under 3.5 wt.% NaCl environment