Thermo-hydraulic and entropy generation analysis of nanofluid flow with variable properties in various duct cross sections: a 3-D two-phase approach

Anwesha Varma,Kottayat Nidhul
DOI: https://doi.org/10.1007/s10973-024-12940-z
IF: 4.755
2024-03-12
Journal of Thermal Analysis and Calorimetry
Abstract:A three-dimensional computational fluid dynamics (CFD) study is carried out to explore the effect of duct cross section on the thermo-hydraulic performance of various ducts. A finite volume-based scheme with an SST k -omega model and mixture model (two-phase model) was used to obtain more realistic results. A two-phase mixture model was used to consider the movement between base fluid and nanoparticles. Al 2 O 3 nanoparticle having a volume fraction of 0.01% and 42 nm as particle size, the heat transfer and friction factor characteristic are studied for turbulent flow regime (3000 < Re < 9000) with variable thermo-physical properties. A maximum enhancement of 86% in heat transfer rate is obtained for the serpentine duct compared to the conventional circular duct at Re = 4500. Owing to a significantly lower increase in pressure drop, the elliptical duct has the highest thermo-hydraulic performance parameter of 1.54 relative to the circular duct. Further, to analyze the heat transfer quality, the entropy generation rate is studied, and it is observed that the square duct reported the highest with an increase of 60% and the elliptical duct the lowest with a reduction of 54% relative to the circular duct. This study can aid in choosing the duct geometry to enhance the heat transfer rate with nanofluid for applications such as solar-thermal, heat exchangers, etc.
chemistry, physical, analytical,thermodynamics
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to improve the heat transfer efficiency while controlling the pressure loss by studying the flow and heat transfer characteristics of nanofluids in pipes with different cross - sectional shapes. Specifically, the author focuses on the influence of pipes with different geometric shapes (circular, square, triangular, serpentine and elliptical) on the hydro - thermal performance and entropy generation of nanofluids under turbulent conditions (3000 < Re < 9000). Through this research, the author hopes to provide a theoretical basis for selecting appropriate pipe geometries for applications such as solar thermal utilization and heat exchangers. ### Main Research Contents 1. **Research Background**: - Nanofluids have potential application values in many thermal systems due to their enhanced thermal conductivity. - The traditional single - phase model has limitations in simulating nanofluids, so a two - phase model is required to more realistically reflect the interaction between nanoparticles and the base fluid. 2. **Research Methods**: - Use the three - dimensional computational fluid dynamics (CFD) method, combined with the SST k - omega turbulence model and the mixture model (two - phase model) for numerical simulation. - Simulate the flow and heat transfer characteristics of nanofluids in pipes with different cross - sectional shapes (circular, square, triangular, serpentine and elliptical). - Consider the volume fraction of nanoparticles as 0.01% and the particle size as 42 nm, and study the flow characteristics in the range of Reynolds number (3000 < Re < 9000). 3. **Main Results**: - **Heat Transfer Characteristics**: - As the Reynolds number increases, the Nusselt number (Nu) increases in all pipe cross - sections, which is due to the decrease in the boundary layer thickness. - At a Reynolds number of 3000, the serpentine pipe has a maximum heat transfer enhancement rate of 64% relative to the circular pipe. But at higher Reynolds numbers, due to the formation of recirculation zones at the peaks and valleys, the heat transfer enhancement rate decreases to 21%. - The square pipe has the worst heat transfer characteristics, and the Nusselt number is reduced by 54% relative to the circular pipe. - **Friction Factor and Hydro - Thermal Performance Parameter**: - The elliptical pipe has the smallest increase in the friction factor, so its hydro - thermal performance parameter is the highest, which is 1.54 relative to the circular pipe. - **Entropy Generation Analysis**: - The square pipe has the highest entropy generation rate, with an increase of 60%, while the elliptical pipe has the lowest entropy generation rate, with a decrease of 54%. ### Conclusion This research reveals the flow and heat transfer characteristics of nanofluids in pipes with different geometric shapes through numerical simulation and analysis. The results show that the serpentine pipe has the highest heat transfer enhancement rate at a lower Reynolds number, while the elliptical pipe performs best in controlling the pressure loss. These findings are helpful for optimizing the pipe design of heat exchangers and other thermal systems and improving the heat transfer efficiency.