Abstract:The present investigation has employed recycled waste glass powder (WGP) and silicon nitride (Si 3 N 4 ) as reinforcing-agents within AZ91D-matrix composites. The composites were fabricated by employing the vacuum stir casting technique to mitigate the effects of oxidation and to ensure homogeneity, uniformity, and superior wettability among the AZ91D-matrix and reinforcements. A microscopic study provided confirmation of a uniform dispersion of WGP and Si 3 N 4 particles throughout the AZ91D-matrix. The tensile strength of the AZ91D/WGP/Si 3 N 4 composites rise with the inclusion of WGP particulates by up to 1.5 percent in AZ91D/7.5% Si 3 N 4 . However, the tensile strength of the AZ91D/9%Si 3 N 4 composite have showed maximum value as compared to other chosen formulations/combinations in the current investigation. The tensile strength of AZ91D/1.5% WGP/7.5% Si 3 N 4 composites has strengthened up to 12.13 percent with the comparison of base alloy AZ91D-matrix. In A1 formulated composite, the amount of WGP particulate has enhanced the hardness of the AZ91D-alloy by up to 1.5 percent. Findings, nevertheless has exhibited that the A6 formulated composite had superior outcomes in terms of hardness. The incorporation of "reinforcing-constituent particulates" with 1.5%WGP + 7.5%Si 3 N 4 combination within the AZ91D-matrix, has further increased fatigue-strength by around 57.84 percent. A weight-loss of 0.312 mg was being unveiled for the A1 formulated fabricated composite. The weight-loss for the A6 formulated fabricated composite, however, was reported to be 0.294 mg. At 5 N loads, 2 m/s sliding speed, and 1000 m of sliding distance, the developed 1.5%WGP/7.5%Si 3 N 4 /AZ91D composites was reported to have a rate of wear, and frictional coefficient of 0.0025 mm 3 /m and 0.315, respectively. The investigation employing scanning electron microscopy (SEM) identified the presence of corrosion pits on the surfaces that had undergone corrosion. These pits were found to be a result of localised surface assaults occurring in corrosive environments. Additionally, SEM pictures of the worn surfaces indicated the emergence of microcracks, which may be associated to the conditions of cyclic loading. Moreover, the tensile-fractography examination for the developed 1.5%WGP/7.5%Si 3 N 4 /AZ91D composites has exhibited the brittle fracture failure, including cracks and debonding phenomena. In addition, the EDS spectra-analysis have revealed an apparent existence of the observed Mg-peak, Si-peak, Al-peak, Ca-peak, and O-peak for the 1.5%WGP/7.5%Si 3 N 4 /AZ91D composites. Furthermore, the utilisation of X-ray diffraction analysis effectively determined the existence of hard phases inside the AZ91D-matrix, which significantly contributed to the reported enhancement in wear resistance. The development of harder-phases has included, α-Mg, Al 12 Mg 17, SiO 2 , Si 3 N 4 , MgO, and CaO phases within the composite has been accountable for the enhancement of the tribomechanical, and wear-resistance characteristics of the AZ91D/WGP/Si 3 N 4 composites. The Si 3 N 4 has been discovered to have a substantial impact on enhancing mechanical performance and raising the resistance to wear.

Investigation of Reciprocating Wear Characteristics of Nano-B4C Reinforced AZ91D Magnesium Metal Matrix Nanocomposites Prepared Through Ultrasonically Assisted Stir Casting Technique

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Effect of nano/micro B4C particles on the mechanical properties of aluminium metal matrix composites fabricated by ultrasonic cavitation-assisted solidification process

Abrasive Wear Behavior of AZ31−B4C Composites

Micro-mechanical and tribological behavior of Al/SiC/B4C/CNT hybrid nanocomposite

Effect of B4C and SiC nanoparticle reinforcement on the wear behavior and surface structure of aluminum (Al6063-T6) matrix composite

Abrasive wear behavior of WC nanoparticle reinforced magnesium metal matrix composites

Processing and Evaluation of Mechanical Properties and Dry Sliding Wear Behavior of AA6061-B4C Composites

Effect of Multi-Walled Carbon Nanotubes and Carbon Fiber Reinforcements on the Mechanical and Tribological Behavior of Hybrid Mg-AZ91D Nanocomposites

Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles

Microstructure, mechanical and wear properties of boron carbide reinforced nickel alloy composites processed by bottom pouring type stir casting process

Exploring the mechanical and structural properties of B 4 C/ZrO 2 strengthened Al-Mg-Cr alloy hybrid composites

Effect of CNTs on microstructure, mechanical and wear properties of the AZ91–3B 4 C–3SiC– x CNTs composites

Enhancing tribo-mechanical, microstructural morphology, and corrosion performance of AZ91D-magnesium composites through the synergistic reinforcements of silicon nitride and waste glass powder

Influence of B4C on Dry Sliding Wear Behavior of B4C/Al–Mg–Si Composites Synthesized via Powder Metallurgy Route

Nano-particle Reinforced Magnesium Matrix Composites

Wear Performance of TiB2-Reinforced AZ91 Magnesium Metal Matrix Composite Fabricated by Ultrasonic Stir-Casting Process

Effect of TiC Reinforcement on Mechanical and Wear Properties of AZ91 Matrix Composites

Tribological behavior of in-situ nanosized TiB2 particles reinforced AZ91 matrix composite

Synthesis and Experimental Investigations of Tribological and Corrosion Performance of AZ61 Magnesium Alloy Hybrid Composites

Synergistic Effect of Ex Situ and In Situ Reinforcements on the Dry Reciprocating Wear Behavior of AA6061-B4C Composite Fabricated Using Varying K2TiF6 Flux Content