Abstract:The present investigation highlights the development of high-performance materials in the construction materials industry, with a special focus on the production of aluminium matrix composites (AMCs) containing titanium carbide (TiC) particles. The stir casting method with ultrasonic assistance was employed to enhance the mechanical and tribological properties. ASTM standards were employed to evaluate the influence of TiC particles on density, hardness (VHN), ultimate tensile strength (UTS), and wear resistance at various TiC weight fraction percentages (0.0 wt.%, 2.0 wt.%, 4.0 wt.%, 6.0 wt.%, and 8.0 wt.%). Field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) analysis were performed to analyse the microstructural changes and elemental phases present in the synthesised composite. Results revealed that the incorporation of 8 wt.% TiC reinforcement in the metal matrix composites demonstrated significant improvements compared to the base alloy. In particular, a substantial enhancement in hardness by 32%, a notable increase of 68% in UTS, and a significant 80% rise in yield strength were observed when contrasted with the pure aluminium alloy. The tensile fracture analysis of the specimens revealed the presence of dimples, voids, and cracks, suggesting a brittle nature. To assess the wear characteristics of the composites, dry sliding wear experiments were performed using a pin-on-disc wear tester. Incorporation of TiC particles resulted in a lower coefficient of friction than the base alloy, with the lowest friction coefficient being recorded at 0.266 for 6 wt.% TiC, according to the data. FESEM and energy-dispersive X-ray spectroscopy (EDXS) were used to examine the surfaces of the worn pin. Overall, the inclusion of TiC reinforcement particles in the matrix alloy greatly enhanced the wear resistance and friction coefficient of the Al-6TiC composites. Ploughing and adhesion under lower loads and delamination under higher loads were the wear mechanisms observed in the wear test.

Effect of TiC Reinforcement on Mechanical and Wear Properties of AZ91 Matrix Composites

Influence of TiC content on mechanical, wear and corrosion properties of hot-pressed AZ91/TiC composites

The Effect of TiB2 Content on Wear and Mechanical Behavior of AZ91 Magnesium Matrix Composites Produced by Powder Metallurgy

Effect of Ti6Al4V reinforcement particles on the mechanical, wear, and corrosion properties of AZ91D magnesium matrix composites

Characterization and Strengthening Mechanism of CNT/TiB2 Particulates added AZ91D Composites

Influence of TiC Particles on Mechanical and Tribological Characteristics of Advanced Aluminium Matrix Composites Fabricated through Ultrasonic-Assisted Stir Casting

Tribological behavior of in-situ nanosized TiB2 particles reinforced AZ91 matrix composite

Wear Performance of TiB2-Reinforced AZ91 Magnesium Metal Matrix Composite Fabricated by Ultrasonic Stir-Casting Process

Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles

Effect of Ti particles on microstructure and mechanical properties of Mg–9Al–1Zn based composite sheets

Microstructure, mechanical properties and wear resistance of Ti particles reinforced AZ31 magnesium matrix composites

Effect of Titanium Dioxide Particles on the Morphology, Mechanical, and Wear Properties of the Aluminum Alloy 3003-Based Composites

Effect of Ti particles on microstructure and mechanical properties of TiP/AZ91 composites

Mechanical Properties Enhancement of AZ91 Magnesium Alloy Reinforced with Various Ratios of Titanium Particles and Processed by ECAP

Effect of in situ TiC reinforcement and applied load on the high-stress abrasive wear behaviour of zinc–aluminum alloy

Effect of in-situ (TiC-TiB2) reinforcement on aging and mechanical behavior of AZ91 magnesium matrix composite

Investigation of Mechanical and Tribological Properties of Al6061–TiB2 Metal Matrix Composites

Tribological, mechanical and microstructure characteristics of hybrid aluminium matrix composite containing titanium carbide (TiC) and graphite particles

Microstructures and the improved mechanical properties of AZ91 alloy by incorporating Ti-6Al-4V particles

Influence of Ti-6Al-4V particles on the interfacial microstructure and strength-ductility synergetic mechanism of AZ91 magnesium alloy

Development of wear maps of in-situ TiC+TiB2 reinforced AZ91 Mg matrix composite with varying microstructural conditions