Abstract:Mechanism analysis, process optimisation and validation of laser surface treatment. Adhesive bonding has gradually replaced mechanical connections as the primary method for composite material bonding, with surface quality being the key factor determining the effectiveness of composite material adhesion. Laser surface treatment, known for its green and precise characteristics, has garnered widespread attention from both academia and industry. However, the process parameters of laser surface treatment are complex, efficiency is low, and the mechanism remains unclear. This paper, based on the response surface methodology (RSM), investigates the influence of laser secondary parameters on the resin removal rate of carbon fiber reinforced polymer/plastic (CFRP) surfaces and the impact of defocusing on surface treatment efficiency. The results indicate that when the total laser energy density (Et) is 69 J/cm2, the overlap ratio in the warp direction (OLs) is 76%, and the overlap ratio in the weft direction (OLh) is 85%, the surface tensile shear strength increases by 90.59% and 27.77% compared to the original surface and polished surface, respectively. When the defocus distance is +8 mm, the efficiency of laser surface treatment is 2.25 times that of non‐defocus, with minimal impact on mechanical performance. The surface treatment mechanism, with changes in Et, primarily involves the pure thermal decomposition of the resin matrix in an oxygen‐free environment, oxidative decomposition, and the synergistic action of the decomposition products' oxidation. Through the coupled optimization of laser process parameters, this work enhances the efficiency and effectiveness of composite material adhesive surface treatment, promoting the engineering application of laser technology. Highlights By establishing a response surface model, the study elucidated the impact patterns of laser secondary parameters (overlap rates in the warp and weft directions, total energy density) on the resin removal rate of CFRP surfaces. Based on the laser surface treatment phenomena at different total energy densities, the study analyzed and revealed the mechanism of near‐infrared (1064 nm) laser resin removal from CFRP surfaces. By increasing the spot size through defocusing, the efficiency of laser surface treatment was enhanced, and the impact on the interfacial properties of CFRP after defocused treatment was validated.

Advancements in metaheuristic optimization techniques for laser beam cutting of FRP composites: A review

Optimization of heat affected zone in laser cutting of Kevlar-29 fiber composite using hybrid response surface based grey wolf optimization (RSGWO) algorithm

Multi-Response Optimization of Abrasive Waterjet Cutting on r-GO-Reinforced Fibre Intermetallic Laminates through Moth–Flame Optimization Algorithm

A Review of Research Progress on Machining Carbon Fiber-Reinforced Composites with Lasers

A review on machine learning implementation for predicting and optimizing the mechanical behaviour of laminated fiber-reinforced polymer composites

Multi-objective optimization of fiber laser cutting quality characteristics of glass fiber reinforced plastic (GFRP) materials

Current Concepts for Cutting Metal-Based and Polymer-Based Composite Materials

Optimization of Kerf Width in WEDM of Sandwich Woven CFRP-An Ensemble Machine Learning Based Approach

Multi-objective Optimization of Kerf-taper and Surface-roughness Quality Characteristics for Cutting-operation On Coir and Carbon Fibre Reinforced Epoxy Hybrid Polymeric Composites During CO2-Pulsed Laser-cutting Using RSM

Development of Laser Processing Carbon-Fiber-Reinforced Plastic

A combined approach of artificial neural network, multi-objective genetic algorithm, and response surface methodology for enhanced PMMA micro-channeling in low power fiber laser beam machining

Development of Laser Drilling Strategy for Thick Carbon Fibre Reinforced Polymer Composites (CFRP)

Experimental investigation of sawing approach of low power fiber laser cutting of titanium alloy using particle swarm optimization technique

Investigation on Polymer Hybrid Composite Through CO2 Laser Machining for Precise Machining Conditions

Investigation on mechanism for water-gas jet-assisted laser processing of carbon fiber-reinforced polymer

Process optimization and performance verification of CFRP laser surface modification

Optimization of Laser Cutting Parameters for PMMA Using Metaheuristic Algorithms

Process characteristics, damage mechanisms and challenges in machining of fibre reinforced thermoplastic polymer (FRTP) composites: A review

State-Of-The-Art and Trends in CO2 Laser Cutting of Polymeric Materials-A Review

Investigating the Technology of UV Nanosecond Laser Milling for Cutting CFRP Laminates.

A review on the fused deposition modelling of fibre-reinforced polymer composites: Influence of process parameters, pre-processing and post processing techniques