Abstract:The traditional way to machine hybrid composites is hard because they tend to break, have a high retraction, have a high service temperature, and have an uneven surface irregularity. For high-strength fiber/metal composite constructions, alternative machining methods have drawn interest as a solution to these problems. Current research focuses on enhancing the Abrasive Water Jet Machining process by optimizing its variables using a composite material of epoxy reinforced with silicon carbide, stainless steel wire mesh, and Kevlar. The variables assessed are the Nozzle-to-substrate gap (S), the Abrasive discharge molding and different percentages of silicon carbide (SiC) filler (0%, 3%, and 6% by weight), three different types of hybrid laminates (H1, H2, and H3) were produced. The response surface method (RSM) was utilized in this learning, specifically on a central composite design, to calculate and optimize machining variables based on the Kerf convergence ratio (Kt) and Surface irregularity (Ra) as responses. According to the results, the traverse feed velocity, Abrasive discharge proportion, and Nozzle-to-substrate gap are the critical factors in determining Surface irregularity and Kerf convergence width (H1 laminate) for a fiber/metal laminate with 0%, 3% and 6% weight fraction. In the case of a 3% weight fraction H2 laminate, the traverse feed velocity was identified as the primary factor affecting the Kerf convergence ratio. In contrast, traverse feed velocity and Nozzle-to-substrate gap had the most significant influence on Surface irregularity. The findings also indicated that S, followed by Abrasive discharge proportion and traverse feed velocity, are the variables that have the most significant influence when cutting 6 wt% SiC filler particle fiber/metal laminate (H3 laminate). For Surface irregularity, the combination of traverse feed velocity and Nozzle-to-substrate gap had the most significant impact. To validate the optimization results, confirmatory tests was conducted, and the findings were very similar to the experimental values, indicating the accuracy and effectiveness of the optimization process. To better understand the manufacturing processes, a scanning electron microscope was used to examine the morphological features of the machined surfaces, such as delamination, fibre breakage, and fibre pull-out.

Optimization of Kerf Width in WEDM of Sandwich Woven CFRP-An Ensemble Machine Learning Based Approach

Optimizing processing parameters in electrical discharge milling of CFRP using metaheuristics

Multi-Response Optimization of Abrasive Waterjet Cutting on r-GO-Reinforced Fibre Intermetallic Laminates through Moth–Flame Optimization Algorithm

A Unified Geometrical Modeling and Analysis Method for Evaluating CFRP Machining Performance: Cutting Geometry Space

A standard deviation based firefly algorithm for multi-objective optimization of WEDM process during machining of Indian RAFM steel

Intelligent Modeling and Multi-Response Optimization of AWJC on Fiber Intermetallic Laminates through a Hybrid ANFIS-Salp Swarm Algorithm

Multifactor Optimization for Induction Welding of Carbon Fiber Reinforced Thermoplastic Composites Based on Response Surface Methodology

A Comprehensive Study on the Optimization of Drilling Performance in Hybrid Nano-Composites and Neat CFRP Composites Using Statistical and Machine Learning Approaches

Modeling and multi-objective optimization of abrasive water jet machining process of composite laminates using a hybrid approach based on neural networks and metaheuristic algorithm

Optimization of heat affected zone in laser cutting of Kevlar-29 fiber composite using hybrid response surface based grey wolf optimization (RSGWO) algorithm

Simultaneous optimization of process parameters during abrasive water jet machining on glass fibre reinforced polymer

A hybrid approach for machining optimization of the WEDM using grey-fuzzy with Metaphor-Less algorithms for Ti-3Al-2.5V

Chip Formation and Orthogonal Cutting Optimisation of Unidirectional Carbon Fibre Composites

Enhancing WEDM performance on Mg/FeCoCrNiMn HEA composites through ANN and entropy integrated COCOSO optimization

Optimizing the Parameters of Carbon Fiber Reinforced Plastic Composite Drilling Process Using Signal-to-noise Ratio-based Grey Wolf Optimization Algorithm

A soft computing-based study on WEDM optimization in processing Inconel 625

Optimizing Process Parameters in Drilling of CFRP Laminates: A Combined MOORA–TOPSIS–VIKOR Approach

Effect of silicon carbide on kerf convergence and irregularity of the surface during abrasive water jet machining of fiber-metal hybrid composites

Abrasive water jet machining of glass fibre reinforced polymer composite: experimental investigation, modelling and optimization

Integrating response surface methodology and machine learning for analyzing the unconventional machining properties of hybrid fiber‐reinforced composites

WEDM of Al/SiC/Ti composite: A Hybrid Approach of RSM-ARAS-TLBO Algorithm