Abstract:The method for preparation of foam concrete from solid wastes were proposed in this study, where soda residue (SR), calcium carbide slag (CS), grand granulated blast-furnace slag (GGBS) and fly ash (FA) were used as raw materials for the binder and Al powder was used as the foam agent. The effects of Al powder, stabilisers and FA content on the dry density as well as compressive strength were assessed to determine the optimal mix proportions. Moreover, to understand the foaming process, the influence of stabilisers on the zeta potential and surface tension of the fresh mixes were measured and Low-Field Nuclear Magnetic Resonance (LF-NMR) was employed to qualitatively characterize the pore size distribution . Finally, the hydration products were analyzed by X-Ray Diffraction (XRD), Fourier transform infrared spectrometer (FTIR), Thermogravimetric Analysis-Differential scanning calorimetry (TGA-DSC), Scanning electron microscope-Energy dispersive X-ray spectroscopy (SEM-EDS). The results suggested that the optimal content of Al powder was 1–2%, and the combination of S and P (SP) stabilisers showed better stabilization effect than the single use of S or P, leading to well distributed foam with smaller size. The stabilization effect was attributed to the dissolved negative complex that absorbed on the foam film to increase the repulsion between foams as well as to reduce the surface tension of the fresh mixture. The substitution of GGBS by FA generally resulted in reduced dry density and compressive strength, while the extent varied with the addition of stabilizers, and thus the optimal amount of FA depended on the selection of stabilisers. Overall, our study highlighted the potential of using industrial waste materials for producing sustainable light weight concrete with satisfactory dry density and compressive strength.

Mechanical Properties of Aluminium Matrix Syntactic Foams Manufactured with Aluminium Smelter Waste

Preparation and Compressive Performance of an A356 Matrix Syntactic Foam

Enhancement in the Mechanical Properties of Newly Developed Ceramic Reinforced Al-Based Syntactic Foams: Analysis of Microstructure, Mechanical Response, and Energy Absorption Properties

Enhanced energy absorption and microstructural studies on hollow glass microsphere filled closed cell aluminum matrix syntactic foam

Compressive Characteristics of Aluminum-Fly Ash Syntactic Foams Processed by Microwave Sintering

Reinforcement Effect of Fly Ash with Different Morphologies on Aluminum Foam Prepared Via Powder Metallurgy

Interface characterization and mechanical property of an aluminum matrix syntactic foam with multi-shelled hollow sphere structure

Development of Porous Tungsten Mud Waste-based Alkali-activated Foams with Low Thermal Conductivity

Preparation of foam concrete from solid wastes: Physical properties and foam stability

Effects of particle size, bimodality and heat treatment on mechanical properties of pumice reinforced aluminum syntactic foams produced by cold chamber die casting

Microstructure and Compressive Properties of Aluminum Foams Made by 6063 Aluminum Alloy and Pure Aluminum

Synthesis and Characterisation of Floatable Magnesium Alloy Syntactic Foams with Hybridised Cell Morphology

Fabrication and characterization of aluminum foam reinforced with nanostructured γ-Al2O3 via friction stir process for enhanced mechanical performance

Micro-CT in the mechanical properties and energy absorption of closed-cell aluminium foam

Mechanical Properties of Aluminium Foam and How Density, Temperature, and Strain Rate Affect Dynamic Strain–Stress Relationship

Effect of Heat Treatment on the Microstructure, Compressive Property, and Energy Absorption Response of the Al–Mg–Si Alloy Foams

Compressive behavior and energy absorption analysis of casting skin-wrapped aluminum foams

Synthesis of metakaolin-based geopolymer foamed materials using municipal solid waste incineration fly ash as a foaming agent

Investigation on the Structural and Mechanical Properties of Al Foam Manufactured by Spark Plasma Sintering and Compression Molding Methods

Collaborative Disposal of Multisource Solid Waste: Influence of an Admixture on the Properties, Pore Structure and Durability of Foam Concrete

Supramolecular metallic foams with ultrahigh specific strength and sustainable recyclability