Abstract:The microstructure evolution and fracture behavior of Ti-5Al-3Mo-3V-2Zr-2Cr-1Nb-1Fe (Ti-5321) alloy during BASCA (β annealed with subsequent slow cooling & aging) heat treatment were studied. Three different lamellar microstructures, termed as L1, L2 and L3, were obtained by solution treated at 880 °C for 2 h followed by 0.5 °C/min cooling to 800 °C, 750 °C and 710 °C, respectively and aging at 580 °C for 6 h. Microstructural investigation revealed that the three lamellar microstructures were composed of intergranular precipitation (αGB, αWGB), intragranular αl and βt. Both of the volume fraction of lamellae α and the size of α colonies increased with the increasing furnace cooling time. Both intergranular and intragranular precipitation in L1, L2 and L3 obeyed the Burgers orientation relationship (OR) with adjacent β grain. However, the texture intensity and variant selection degree of lamellar α increased with cooling process owing to the increased amount of α colonies. In addition, the L1 sample, with 15% αl, displayed the lowest fracture toughness value (57.7 MPa·m1/2), while the L3 sample with 61% αl exhibited the highest (114 MPa·m1/2). Although the crack path in all the cases were both translamellar and interlamellar, fracture mode varied from mixed mode (dimples and intergranular cracks) type fracture in L1 to predominantly dimple fracture in L2 and L3. Moreover, the fracture behavior of Ti-5321 alloy was also related to the crystallographic distribution and variation selection of α phase. Crack growth was much easier through continuous αGB layer compared to the discontinuous αGB, especially for the high angled αGB/αGB grain boundary. As a consequence, the higher probabilities of misorientation angles of 90° in L1 and L3 could significantly promote crack deflection compared to L2.

Fractal fracture of amorphous Fe46Ni32V2Si14B6 alloy

Effect of V Substitution for Nb on the Crystallization Kinetics of FINEMET Amorphous Alloys

Temperature Dependence of the Fracture Toughness <i>J<sub>C</sub></i> of Random Fibrous Material

Temperature Dependence Of The Fracture Toughness J(C) Of Random Fibrous Material

Fractal Analysis of Mo and Nb Effects on Grain Boundary Character and Hot Cracking Behavior for Ni-Cr-Fe Alloys

Temperature-dependent Mechanical Properties and Fracture Behavior of Directionally Solidified Ti47Al2Cr2Nb Alloy

Numerical and Experimental Fracture Study for 7003 Aluminum Alloy at Different Triaxialities

Microstructure evolution and fracture behavior of Ti-5Al-3Mo-3V-2Zr-2Cr-1Nb-1Fe alloy during BASCA heat treatments

Investigations on Fracture Toughness and Fracture Surface Energy of 3D Random Fibrous Materials at Elevated Temperatures

A FRACTAL STUDY ON BRITTLE-DUCTILE TRANSITION FOR TI-24AL-11NB ALLOY

Exceptional fracture toughness of CrCoNi-based medium- and high-entropy alloys close to liquid helium temperatures

Anomalous Increase of Fracture Toughness of TiAl-based Alloys at High Temperature

Fracture toughness of random fibrous materials with ultrahigh porosity at elevated temperatures

Investigating the ductile to brittle transition phenomenon in binary Fe-Ni systems using molecular dynamics simulation

Anisotropy in Fracture Toughness and Toughening Mechanism of Ti-22Al-25Nb Alloy Related to Texture and Grain Boundary Damage

ON THE TIME-DEPENDENT MATERIAL FRACTURE TOUGHNESS AT HIGH TEMPERATURE

On the Brittle-to-Ductile Transition of the As-cast TiVNbTa Refractory High-entropy Alloy

Fractal behavior of amorphous metal structure under the action of tensile stress

Fractal Size Distribution of Debris of Al-Based Nanocrystalline Alloy Fractured in A Wide Strain-Rate Range

Influence of an Electric Field on the Quench Aging of a Medium-Carbon Alloy Steel

Exceptional fracture toughness of CrCoNi-based medium- and high-entropy alloys at 20 kelvin