Abstract:Large-diameter monopiles are the predominant foundation solution for supporting offshore wind turbines. They are conventionally designed using soil reaction curves developed for long slender piles used for supporting offshore oil and gas platforms (e.g., the API p-y model). However, due to the difference in the length/diameter ratio and the resulting soil mechanisms, the use of p-y curves alone can lead to significant under-prediction of the lateral stiffness and capacity of monopiles. To overcome the shortcoming, the authors have previously proposed a conceptual two-spring framework, i.e., the so-called 'p-y + M-R-theta(R)' model, to capture the monopile response in soft clay under lateral loading. The framework uses distributed p-y springs to consider the lateral soil resistance along the pile above the rotation point (RP) and a single moment-rotation (M-R-theta(R)) spring attached at the RP to capture the entire soil resistance below the RP, i.e., the distributed resistance along the pile, base shear and base moment at the pile tip. The proposed p-y and M-R-theta(R) springs were curve-fitted to the results of 3D numerical analyses. However, as the stress-strain response and the shear strength profile inevitably influence the p-y and M-R-theta(R) springs, the applicability of the empirical formulations to soil conditions other than those examined is uncertain. This study proposes an enhancement to the 'p-y + M-R-theta(R)' framework, in which the p-y and M-R-theta(R) springs are not tied to a specific soil and strength profile but fundamentally linked to the properties that can be measured directly in the site investigation and laboratory. This extension is achieved through analytical analyses and an extensive parametric numerical study. The predictive capabilities of the model are demonstrated by back-analyses of finite element analyses and centrifuge model tests. The proposed model provides practising engineers with a simple yet powerful approach to use site-specific soil reaction curves in the design of monopiles embedded in soft clay.

A cyclic-softening macro element model for mono-bucket foundations supporting offshore wind turbines in clay

A Strength Degradation Model of Saturated Soft Clay and Its Application in Caisson Breakwater

Long-Term Lateral Cyclic Response of Suction Caisson Foundations in Sand

Centrifuge Modelling of Lateral Loading Behaviour of a “Semi-Rigid” Mono-pile in Soft Clay

An Investigation into the Lateral Loading Response of Shallow Bucket Foundations for Offshore Wind Turbines Through Centrifuge Modeling in Sand

Cyclic moment loading of suction caissons in sand

Lateral Cyclic Pile–soil Interaction Studies on a Rigid Model Monopile

Centrifuge model test on suction caisson foundation in soft clay subjected to lateral loads

Cyclic accumulative deformation of sand and its explicit model

Analysis and Design of Bearing Capacity of Suction Caisson Foundations of Offshore Wind Turbines

A Numerical Study on the Lateral Loading Behaviour of Offshore Tetrapod Piled Jacket Foundations in Clay

Centrifuge Modelling of Lateral Cyclic Behaviour of a Tetrapod Piled Jacket in Soft Clay

Enhanced Multi-Springs Model for Estimating Suction Caisson Responses under Cyclic Lateral Loading

A Bounding-Surface-based Cyclic "P-Y Plus M-θ" Model for Unified Description of Laterally Loaded Piles with Different Failure Modes in Clay

Site-specific soil reaction model for monopiles in soft clay based on laboratory element stress-strain curves

A Simple Bounding Surface Elasto-Viscoplasticity Model for Marine Clays under Monotonic and Cyclic Loading

Macro-element modeling of suction caisson subjected to vertical tensile loading via up-scaling soil stress-strain relations

A Multi-Axial Bounding Surface P-Y Model with Application in Analyzing Pile Responses under Multi-Directional Lateral Cycling

Modelling of suction bucket foundation in clay: From finite element analyses to macro-elements

Multi-springs Model for Suction Caisson under Monotonic Lateral Loading

On Load-Bearing and Soil-Reacting Characteristics of Hybrid Pile-Bucket Foundations Subjected to Static Horizontal Loading