Abstract:As humanity is confronted by climate change, electrochemical CO 2 reduction has become an important strategy for generating value-added chemicals whilst lowering carbon emissions. In this work, Cu 2 O nanoparticles with different morphologies and predominant exposed crystal facets, including nanocubes (Cu 2 O-NC) with (100) facets, nanoflowers (Cu 2 O-NF) with (110) facets, and octahedral structures (Cu 2 O-O) with (111) facets, are prepared, and compared as catalysts for the electrochemical CO 2 reduction to C 2+ products in a flow cell electrolyzer, to overcome the mass transfer limitations of CO 2 in an H-cell and reach industrially relevant currents. To maximize the performance towards C 2+ products, a parameter optimization ( i.e. pH and current) was performed. Under the conditions of 150 mA cm −2 and pH of 8.5, the Cu 2 O-NC revealed a maximum faradaic efficiency of 58% for C 2+ products. Similar studies in an H-cell system have shown lower total C 2+ FE of around 35–40% for the nanocubes, indicating an improvement and showcasing the advantages of using a gas-fed flow electrolyzer. Finally, the long-term stability of these materials was also evaluated. The results revealed that C 2+ activity remains constant for four hours at 50%. However, a sharp decline was observed after five hours when GDE flooding occurs, leading to a dominant HER. To confirm, the electrode was washed and dried before re-utilizing it. Since the Cu 2 O largely recovers its initial C 2+ activity (from 50% to 43%) albeit with a slightly different product composition, this confirms GDE flooding as the main cause of degradation. During the eCO 2 RR, Cu 2 O is reduced to metallic Cu, as proven by in situ Raman. As a result, the particle morphology is roughened, which is proven by ex situ SEM images. Subsequently, water penetrates the gas diffusion electrode more easily, inhibiting the diffusion of CO 2 , and alongside the electrowetting effect results in GDE flooding. In conclusion, this work explores the utilization of different Cu 2 O catalysts in a flow electrolyzer, revealing insights into higher currents, their stability issues, crystal facet dependency, and reaction environment, which was unexplored in previous literature where the focus was on H-cell testing, which evaluates the catalysts under less demanding and more controlled conditions that are less relevant for up-scaling and eventual commercialization. Based on these new insights, further improvements can be made to enhance the total C 2+ FE and improve stability.

Study of CuSb bimetallic flow-through gas diffusion electrodes for efficient electrochemical CO 2 reduction to CO

Self-supported copper-based gas diffusion electrodes improve the local CO2 concentration for efficient electrochemical CO2 reduction

Additive-Assisted Electrodeposition of Cu on Gas Diffusion Electrodes Enables Selective CO 2 Reduction to Multicarbon Products

Additive-Assisted Electrodeposition of Cu on Gas Diffusion Electrodes Enables Selective CO2 Reduction to Multicarbon Products

Superaerophilic copper nanowires for efficient and switchable CO 2 electroreduction.

Selective CO2 electrolysis to CO using isolated antimony alloyed copper

CuC(O) Interfaces Deliver Remarkable Selectivity and Stability for CO2 Reduction to C2+ Products at Industrial Current Density of 500 mA cm−2

Scalable Gas Diffusion Electrode Fabrication for Electrochemical CO2 Reduction Using Physical Vapor Deposition Methods.

From batch to flow: the effect of pH, current, and the crystal facets of Cu2O on electrochemical CO2 reduction

Intermetallic Copper–Antimony Alloy for Enhanced Electrocatalytic CO2 Reduction to CO

Electronic Delocalization of Bismuth Oxide Induced by Sulfur Doping for Efficient CO 2 Electroreduction to Formate

High‐Density CuInS2 Quantum Dots for Efficient and Stable CO2 Electroreduction

Hydrophobic 1-octadecanethiol functionalized copper catalyst promotes robust high-current CO2 gas-diffusion electrolysis

Copper hollow fiber electrode for efficient CO2 electroreduction

Oxidation-induced Restructuring of Copper Sulfides for Enhanced Performance in CO2 Electroreduction

Tuning Sb Atoms on Cu‐Based Catalysts for Electrochemical Conversion of CO2 to Syngas

Cobalt Doping in MOF-Derived Carbon-Loaded Tin Nanomaterials for Enhanced Electrocatalytic CO 2 Reduction

Hollow fiber gas-diffusion electrodes with tailored crystal facets for tuning syngas production in electrochemical CO 2 reduction

Selective Reduction of CO2 to CO on an Sb-Modified Cu Electrode: Spontaneous Fabrication and Physical Insight

Highly Selective Palladium-Copper Bimetallic Electrocatalysts for the Electrochemical Reduction of CO2 to CO

Manipulation of Oxygen Species on an Antimony-Modified Copper Surface to Tune the Product Selectivity in CO2 Electroreduction